CAVITY DRAINAGE
Hohmann & Barnard Mortar/Grout Screen
Mortar/Grout Screen (MGS) is a 1/4″ square monofilament screen fabricated from high-strength, non-corrosive polypropylene polymers which offers the following benefits:
Isolates flow of grout in designated areas requiring reinforced concrete block
Allows for greater bonding of masonry anchor in hollow block construction
Micro-thin material has high tensile and burst strength yet will not interfere with mortar bond
Hohmann & Bernard Mortar Trap
Mortar Trap™ is manufactured from high-density polyethylene (HDPE) strands woven into a 90% open mesh. Its unique shape breaks up mortar droppings and prohibits mortar from creating a moisture retaining barrier, allowing water to flow freely to the weep holes.
Hohmann & Bernard Mortar Web
Mortar Web suspends mortar droppings and redirects moisture to the exterior of the structure. Bypassing mortar collection altogether, moisture is able to dissipate correctly and avoid pooling within the wall. The straight cut and recycled heavy fiber weave makes this product more effective than the alternative pea gravel application. Mortar Web will not aid in the growth of mold, mildew or fungus. It is equal or superior to other mortar collection devices on the market, but sold at a fraction of the cost.
Hohmann & Barnard Mortar Trap Weep Vents
A 100% recycled polyester plastic non-woven mesh vent which is treated with a flame retardant and ultra-violet inhibitors. Used in vertical joints between brick masonry in masonry wall construction to provide for the drainage of moisture and promotion of air flow. The weep vents also prevent insects from entering through the openings.
Hohmann & Barnard Quadro-Vent
QV – Quadro-Vent’s honeycomb design allows passage of moisture from cavity to the building exterior while restricting ingress of insects and other debris
Quadro-Vent™ allows passage of moisture up to its 2 1/2″ height, important in the event of mortar droppings at bottom of the cavity
Polypropylene tested in conformance with ASTM D2240, D790B, D638 and D1238B
Also suitable for top of wall venting.
AVAILABLE FINISHES:
Black, Grey, Clear, Almond, Buff, Cocoa, or White
Hohmann & Barnard Rectangular Plastic Weep
342 Rectangular plastic weep holes provide an outlet for water inside a building to move outside the wall and evaporate, they are manufactured from Clear Butyrate.
Hohmann & Barnard Round Weep Vent
341 Series Round Plastic Weep Holes provide an outlet for water inside a building to move outside the wall and evaporate, they are manufactured from Medium Density Polyethylene (white)
Hohmann & Barnard 343 Weep Hole
343 Weep Hole features louvers configured to direct the passage of water from the wall cavity to outside of building, while inhibiting reverse passage of water
MortarNet BlockNet
The BlockNet CMU single wythe flashing solution reliably protects CMU walls from water infiltration damage by enabling moisture to easily drain from the block cell interiors to the building exterior.
MortarNet with Insect Barrier
MortarNet helps prevent moisture damage to masonry cavity walls by preventing mortar droppings from blocking the weep holes and by providing hundreds of clear drainage pathways that allow moisture to flow to the weeps. It’s open mesh also allows air movement to help equalize pressure and dry the cavity.
MortarNet BlockFlash
BlockFlash is a complete, embeddable flashing solution for managing moisture in exterior single wythe CMU walls. It uses patented flashing pans to collect moisture in the wall and channel it to the exterior through integrated weep spouts. Its included drainage mesh provides hundreds of clear pathways for water to flow around mortar droppings inside the block cells so it can be collected by the pans.
MortarNet Total Flash
The patented TotalFlash Cavity Wall Drainage Solution is a complete, factory-assembled masonry cavity wall flashing system that cuts labor costs and provides better performance than standard through wall flashing. It combines a flashing membrane with a mortar dropping collection drainage mat, weep tabs, drip edge and termination bar into a single, easy-to-install panel.
MortarNet Cell Vents
CellVent is a key component of a masonry cavity wall drainage system. It allows moisture to drain from the cavity while restricting insects and debris from entering the cavity. It also allows air to move in and out of the cavity, which helps prevent air pressure differentials that can force moisture into the cavity and which allows the wall to dry properly.
CellVent are fabricated from durable polypropelyene and are UV stabilized for long life. They are available in 7 colors to complement most wall designs.
MortarNet Weep Vents
WeepVent for masonry cavity walls helps ensure that moisture can migrate out and air can circulate into the cavity, and that insects can’t enter the cavity through the weep holes. The product’s compressibility means it can completely fill the weep holes, and “prickly adhesion” holds the WeepVent in place without fasteners or adhesives.
Wire-Bond Cavity Net Rain Screen
Cavity Net RS is perfect for all exterior siding applications. Our innovative rainscreen technology equalizes the air pressure within the wall system by creating a drainage and ventilation cavity between the weather resistant barrier (WRB) and the exterior wall. This design allows excess moisture to drain from the wall system and allows ventilated air to circulate and dry the interior wall components.
Wire-Bond Cell Vent
#3601 Cell Vent (ultra violet resistant polypropylene co-polymer), consists of many small, adjacent passageways bonded together in one unit. It’s cellular composition provides easy drainage for moisture along the full height of the head joint.
Wire-Bond Cavity Net I and II
Wire-Bond® Cavity Net I and II are popular cost competitive ways to ensure proper cavity wall drainage.These mortar deflection devices ensure that mortar droppings do not block the weep holes at the base of the cavity.
Cavity Net I :
Polymer core geomatrix composed of high density polyethylene strands woven into a .80″ thick mesh
The design allows moisture to seep down through any mortar droppings and exit the cavity wall through the weep holes. Used in cavity walls ranging from 1″ to 1-3/4″ in width.
Cavity Net II :
1.5″ thick high-density polyethylene geometric design used for cavities 2″ and wider.
The staggered dimples design suspend mortar droppings and redirect moisture to the exterior by way of the weep holes.
The slightly narrower design helps avoid any possible bridging of mortar across the cavity.
Wire-Bond Cavity Net DT
Cavity Net DT™ is used in masonry cavity wall construction. Manufactured from high-strength nylon with a 95% open three-dimensional matrix.
Cavity Net DT™ allows air and water to flow freely. Its unique dovetail shape with continuous base suspends mortar droppings at two levels preventing mortar bridging and allows moisture to exit the wall through weeps or vents.
CLEANERS
Prosoco Sure Klean 600 New Masonry Cleaner
PROSOCO Sure Klean® 600 is the No. 1-selling proprietary cleaner for new masonry and is recommended by many brick, block, tile and mortar manufacturers. This general purpose, concentrated acidic cleaner dissolves mortar smears and construction dirt quickly, leaving the masonry clean and uniform with no acid burning or streaking. Safer than muriatic acid for new masonry surfaces. It removes efflorescence on bricks, new concrete and new stone construction. Application is fast and easy with a cold-water rinse. Special wetting agents let larger masonry surfaces be cleaned at one time, eliminating streaking.
Available in 1-gal, 5-gal, & 55-gal
Prosoco Sure Klean Vana Trol
Vana Trol is a concentrated acidic cleaner for new masonry surfaces that are subject to vanadium, manganese and other metallic stains. Vana Trol is designed to simplify rinsing and reduces the potential for efflorescence.
Available in 1-gal, 5-gal, & 55-gal
Prosoco Sure Klean 101 Lime Solvent
Sure Klean 101 Lime Solvent is a concentrated acidic cleaner for dark-colored brick and tile surfaces which are not subject to metallic oxidation. It safely removes excess mortar and construction dirt.101 Lime Solvent removes construction dirt and excess mortar with simple cold water rinse and removes efflorescence from new brick and new stone construction. It is safer than muriatic acid on colored mortar and dark-colored new masonry surfaces.
Available in 1-gal, 5-gal, & 55-gal
Prosoco Sure Klean Residential BricKlean
Residential BricKLEAN dissolves hardened excess mortar, construction dirt, efflorescence and grime from newly constructed residential red or dark brick or tile, concrete and decorative concrete. Safer than muriatic acid. Economical concentrate – dilutes with fresh water. Cold-water rinse leaves brick clean and uniform without streaking or burning.
Available in 1-gal & 5-gal
Prosoco Sure Klean Residential BricKlean Plus
Residential BricKLEAN Plus eliminates hardened mortar, efflorescence and common construction soiling from brick, tile, concrete and natural stone. The solution works by first dissolving the soiling agents, allowing them to be easily rinsed away with cold water, and leaving the brick clean and uniform without streaking or burning.
Available in 1-gal & 5-gal
Prosoco Sure Klean Custom Masonry Cleaner
Sure Klean® Custom Masonry Cleaner removes concrete splashes, excess mortar, mud, retarders, heavy efflorescence, embedded stains, rust and surface soiling from textured custom masonry surfaces. This concentrated, general-purpose acidic cleaner improves the color and uniformity of most custom masonry and colored concrete. When used in strong solutions, Custom Masonry Cleaner can be used for additional aggregate exposure (“weathering”).
Available in 1-gal, 5-gal, & 55-gal
Prosoco Sure Klean Light Duty Concrete Cleaner
Sure Klean® Light Duty Concrete Cleaner is specially formulated to remove common construction and atmospheric staining from a variety of substrates, including smooth architectural and engineered concrete, custom masonry, concrete brick, manufactured stone and decorative pavers. This general-purpose, non etching acidic cleaner removes rust, mud, atmospheric dirt, mortar smears and other stains without altering the surface texture. Light Duty Concrete Cleaner adds depth to colors, brightens white matrices and exposed aggregate.
Available in 1-gal, 5-gal, & 55-gal
Prosoco Sure Klean Heavy Duty Concrete Cleaner
Sure Klean® Heavy Duty Concrete Cleaner is formulated for removal of concrete splashes, excess mortar, retarders, heavy efflorescence, embedded stains, rust and surface soiling from textured concrete surfaces. This concentrated, general-purpose acidic cleaner improves the color and uniformity of most standard concrete, colored concrete, precast panel and concrete block surfaces. When used in strong solutions, Heavy Duty Concrete Cleaner will etch concrete, It can be used for additional aggregate exposure ideal for “weathering” architectural concrete.
Available in 1-gal & 5-gal
Prosoco Enviro Klean Safety Klean
Enviro Klean® Safety Klean is an effective, safe alternative to acidic compounds for cleaning brick, tile and concrete surfaces. Safety Klean rids new masonry construction of excess mortar, dirt and other common job site soiling. It’s ideal for projects where traditional acidic cleaners are not allowed. Non-fuming Safety Klean contains no hydrochloric or other traditional inorganic acids and is safe for use on and around most metal surfaces, indoors or out. It is up to 70 percent more effective than citric and glycolic acids, and 50 percent more effective than phosphoric acid.
Available in 1-gal, 5-gal, & 55-gal
Prosoco Enviro Klean 2010 All Surface Cleaner
Enviro Klean® 2010 All Surface Cleaner is a next-generation product for cleaning and degreasing light-to-heavily soiled stone, tile, masonry and much more. Powerful enough for industrial use, flexible enough for jobs around the home, space-saving EK 2010 replaces a host of individual cleaning agents. It’s concentrated for the toughest industrial cleaning jobs on concrete, metal and many other plant and warehouse surfaces. It’s dilutable for home-use on windows, bathroom tub and tile, counter tops and more. Easy-to-use EK 2010 All Surface Cleaner is water-rinsable and contains no harsh acids, caustics or solvents. EK 2010 also removes Sure Klean® Weather Seal Siloxane PD over spray from windows.
Available in 1-gal & 5-gal
Prosoco Sure Klean Heavy Duty Paint Stripper
Sure KIean® Heavy Duty Paint Stripper, an alkaline formula with organic solvents, removes multiple layers of paint and graffiti from masonry surfaces. This “slow-working” extended-contact remover, remains active for 24 hours. One application of Heavy Duty Paint Stripper dissolves heavy accumulations of paint, restoring old masonry to its original appearance. Heavy Duty Paint Stripper contains no methanol, methylene chloride, or chlorinated solvents, and is water-rinsable and nonflammable. Can cut through multiple layers of paint buildup. Highly effective on many common paint coatings. Gel consistency adheres to vertical surfaces; reduces spillage. Can be applied by brush, roller or conventional airless spray equipment.
Available in 5-gal & 55-gal
STIHL RB Pressure Washer
Do you need a powerful pressure washer to tackle your professional cleaning jobs? Whether it’s greasy farm equipment, stained aluminum siding, or a dirty truck, the STIHL RB 600 is ready to rock. It features 3,200 psi of water pressure and 208 cc engine. Its pump components are made of premium commercial-grade Triplex to reinforce its durability. Plus, with the easy start pump system you can start the washer without difficulty or back pressure from the pump. This power washer is designed for handling heavy-duty projects with ease. It also works with a full range of optional accessories, including hose extensions, nozzles and more.
Grout Hog Booger Hog Wall Scrubber
The Booger Hog® significantly cuts the time required for masonry cleaning projects. The innovative design allows easy doorframe and corner cleaning while the swivel head easily accesses hard-to-reach places.
Servicing the Booger Hog is easy. Both grease fittings and the drill motor are simple to replace and self-lubricating bronze bushings improve equipment longevity.
Diedrich Architectural & Specialty Masonry Cleaner
Ideal for use on architectural block and split face block, Diedrich’s Specialty Architectural Masonry Cleaner is specially formulated for the effective removal of construction dirt and atmospheric staining.
Removes mortar smears, rust and mud stains, efflorescence and atmospheric dirt without affecting the texture of the surface
Specialty Masonry Cleaner enhances colors and brightens white substrates and exposed aggregate
Diedrich Concrete Brick & Burnished Masonry Cleaner
Specially formulated Non-Etching cleanser safe for textured and pigmented masonry and mortar surfaces, custom masonry and colored mortar.
Non-etching
Also removes mortar smears, rust and mud stains, and atmospheric dirt without affecting the texture of the surface
Enhances colors and brightens white substrates and exposed aggregate
Diedrich Vana-Stop New Masonry Cleaner
202V Vana-Stop New Masonry Cleaner is specifically formulated for cleaning new masonry susceptible to vanadium, manganese, molybdenum and other metallic stains. 202V Vana-Stop is a productive combination of organic and inorganic acids, wetting agents and inhibitors for use in the professional clean up of new masonry.
Efficiently cleans off residual mortar, efflorescence, job site soiling and staining.
Clean with this product to greatly reduce the likelihood of a staining occurrence and eliminate costly recleaning and stain removal expenses.
Does not discolor or damage surfaces, safer and more controllable than raw muriatic acid.
Diedrich New Masonry Detergent
202 New Masonry Detergent is a general purpose new masonry detergent with a combination of organic and inorganic acids, wetting agents and inhibitors for professional use in the final clean up of new masonry.
Efficiently cleans off residual mortar, job site soiling, staining and efflorescence
Will not discolor or damage masonry surfaces, and is safer and more controllable than raw muriatic acid
CONSOLIDATION TREATMENTS
Prosoco Conservare H100 Consolidation Treatment
For badly deteriorated stone that requires consolidation and protection from water, Conservare H100 is a combination consolidation/water-repellent treatment. This ethyl silicate treatment, modified with a silane water repellent, replaces the natural binding materials while protecting the treated surface from water-related deterioration. H100 may be used on most types of sandstone, limestone, cast stone, stucco, brick and terra cotta. One component – easy-to-use. Low viscosity allows deep penetration. Will not form hardened surface crust. The new binder is mineral – similar to the original stone – no synthetic polymers. Forms no byproducts harmful to the masonry. Good vapor permeability – the treated surface breathes. New binder is acid-resistant – resists acid rain.
Available in 1-qt, 5-gal, & 55-gal
Prosoco Weather Seal H40
Sure Klean® Weather Seal H40 is a deep-penetrating water repellent and consolidation treatment for brick, most natural stone, unglazed terra cotta, historic concrete, stucco and cast stone surfaces. H40 protects against deterioration caused by water and waterborne contaminants while strengthening weathered surfaces and soft mortar joints. Weather Seal H40 also reduces the severity of biological staining common to regions with high relative humidity. It helps prevent the rapid recolonization of biological species such as mold, mildew and lichens that normally thrive on masonry and natural stone architecture.
Available in 1-gal, 5-gal, & 55-gal
Prosoco Conservare OH100 Consolidation Treatment
Conservare OH100 is a ready-to-use consolidation treatment that stabilizes masonry by replacing the natural binding materials lost due to weathering, with silicon dioxide. When properly applied, Conservare OH100 penetrates deeply, does not form a dense surface crust, and retains the substrate’s natural vapor permeability. In addition to the general consolidation of severely deteriorated masonries, Conservare OH100 is an effective pre-treatment for friable substrates that need to be strengthened before cleaning, patching or coating. Conservare OH100 may be used on most types of natural stone, concrete, stucco, brick, terra cotta, etc. One component and easy to use, OH100 strengthens deteriorated stone and features a low viscosity to allow for deep penetration. Will not form hardened surface crust. The new binder is mineral — similar to the original stone — no synthetic polymers.
Available in 1-qt, 1-gal, 5-gal, & 55-gal
FLASHING
Hohmann & Barnard Drip Edges
Our Standard Drip Plate, furnished with a smooth, factory-formed hemmed edge for installation safety and uniform appearance.
Standard DP Drip Plates are compatible with all H&B flashing products.
Hohmann & Barnard EB Spray Tape
Hohmann & Barnard ENVIRO-BARRIER™ Spray-Tape is a spray or brush applied detail flashing for Hohmann & Barnard Air Barriers. It is designed to seal door/window openings, terminations, edges of patches, and overlaps in detail areas.
Hohmann & Barnard Flashing
Hohmann & Barnard produces an extensive line of moisture controlling flashings. Covering all through wall, below grade, and rough opening needs: copper, steel fabric, STPE, asphalt, EPDM, and metal flashing materials are all available. These products can be purchase in sheet rolls, self-adhering liquids, adhesive backed tapes, and in an assortment of colors. No matter the UV resistance requirements, substrate type, or performance needs, H & B has the product to get the job done.
Hohmann & Barnard Liquid Flash
Liquid-Flash is formulated using a high performance silyl-terminated polyether polymer technology (STPE). It is a single component, moisture cure elastomeric waterproofing membrane that is applied and tooled to create a long-term moisture proof barrier. Liquid-Flash shows excellent resistance to UV degradation and extreme environmental conditions. Can be applied to damp or wet substrates without outgassing or “bubbling”. Safe to apply in wet conditions when rain is eminent as it will not wash off like other sealants. Because Liquid-Flash is 100% solids it will not shrink or crack. It is compatible with most common building materials, including concrete, plywood, concrete masonry, brick, gypsum sheathing, wood and cement based sheathings.
Hohmann & Barnard Reglets & Termination Bars
Hohmann & Barnard produces PVC masonry and concrete reglets as well as termination bars. The termination bars are available in aluminum, stainless steel and plastic, and with or without caulking flanges. They are available in a variety of sizes and with predrilled ¼” holes.
Hohmann & Barnard X-Barrier Peel & Stick Barrier
X-Barrier™ is a sheet applied self-adhesive, membrane to provide an air and water barrier when applied to above grade wall assemblies. X-Barrier is a self-adhered membrane that resists air leakage and water penetration and acts as a vapor barrier.
Laticrete MVIS Flexible Sealing Tape
MVIS Flexible Sealing Tape is a flexible, stretchable, and tear resistant flashing detail tape that allows for easy installation in awkward configurations such as arched window or door openings, I-beams, and other wall penetrations. MVIS Flexible Sealing Tape is a self-adhering air, vapor and weather barrier that protects structures from air, vapor, wind, and rain. MVIS Flexible Sealing Tape is a stretchable flashing tape made from an elastic non-woven polyolefin factory laminated to a proprietary adhesive. It can be used as a transition material with MVIS Air & Water Barrier where different substrates meet to provide continuity.
Prosoco FastFlash
FastFlash is a waterproofing, adhesive and detailing compound that combines the best characteristics of silicone and polyurethane. This single-component, silyl-terminated polymer (STP) is easy to gun, spread, and tool, or roller apply to produce a highly durable, seamless, elastomeric flashing membrane. Use FastFlash as a liquid flashing membrane in rough openings, to fill joints and seams, to counterflash waterproofing and air barrier components in new or existing wall assemblies, and to seal around penetrations or protect countersunk fasteners.
Prosoco Joint & Seam Filler
R-Guard Joint & Seam Filler is a gun-grade crack and joint filler, adhesive and detailing compound that combines the best of silicone and polyurethane properties. This single-component, fiber-reinforced, silyl-terminated polymer (STP) is easy to gun, spread and tool. Use Joint & Seam Filler to fill openings and create transitions where flexible reinforcement is required to bridge larger gaps and provide continuous support of fluid-applied flashing membranes, waterproofing or air barrier components.
Wire-Bond Bond-N-Flash
Bond -N- Flash™ Mastic is an all-weather butyl mastic specially formulated to permanently seal all laps, seams and terminations in the application of Bond -N- Flash™ stainless steel membrane flashing.
Wire-Bond Mas-N-Flash
Mas-N-Flash is a high performance self-adhered waterproof membrane that can be applied down to -20°F (-28°C) without the use of primer on most substrates.
Wire-Bond Flashing Mastic
WIRE-BOND® Flashing Mastic is an asphalt base, trowel grade product that dries to a tough flexible waterproof and corrosive proof coating which gives excellent performance over a wide range of temperatures and conditions. WIRE-BOND® Flashing Mastic is a recommended mastic to waterproof all laps and joints in copper based laminated flashing and Aquaflash Flashing.
Wire-Bond Corners & End Dams
WIRE-BOND’s End Dams, Inside Corners and Outside Corners are installed under WIRE-BOND specified flashings for the best protection against moisture penetration at corner sections and end dams .Simply place underneath flashing for the ultimate protection against moisture penetration at corners and end dams.
As opposed to 60 mil fabrics, this product allows smooth transition with flashing materials.
Lays flat for easy installation right out of the box. (Some fabrics are difficult to install in colder weather, requiring a heat gun to flatten.)
Wire-Bond Termination Bar
#4200 Termination Bar is used at top of flashing to secure it to backup and is compatible with all WIRE-BOND flashings.
Wire-Bond Aquaflash 500
Aqua Flash 500 flashing is a composite sheet type waterproofing membrane consisting of 8 mils of high density cross laminated polyethylene bonded to 32 mils of rubberized asphalt for a total thickness of 40 mils.
Keene Driwall Rainscreen
Driwall™ Rainscreen is a drainage mat for exterior wall systems. The entangled net product eliminates incidental moisture problems in most exterior veneer applications, including stucco, manufactured stone, and plank siding. Meets Canadian 10 mm rainscreen code requirement.
Advanced Mortairvent Rain Screen
Mortairvent Rain Screen, perfect for all exterior siding applications. Our innovative RAIN SCREEN technology equalizes the air pressure within the wall system by creating a drainage and ventilation cavity between the weather resistant barrier (WRB) and the exterior wall. This design allows excess moisture to drain from the wall system and allows ventilated air to circulate and dry the interior wall components
GROUTS
Spec Mix Core Fill Grout
In reinforced masonry, SPEC MIX® Core Fill Grout is used to fill cells of concrete masonry units and horizontal bond beams as well as the cavities of composite masonry construction. SPEC MIX Core Fill Grout is available in both Fine and Coarse designs to meet various project specifications. The Core Fill Grouts are dry, preblended products containing cementitious materials and dried aggregates formulated for superior flow to fill masonry voids and achieve required compressive strength while meeting ASTM C 476 and CSA A179 requirements for reinforced masonry construction.
SPEC MIX® Core Fill Masonry Grout is available in 80 lb. (36.3 kg.) packages for easy hand loading or in 3000 lb. (1360.8 kg.) reusable bulk bags to be used with the various SPEC MIX silo systems.
Spec Mix Self Consolidating Grout
SPEC MIX® Self Consolidating Grout (SCG) is a dry preblended grout specifically designed to be highly fluid without segregation of the constituents. SPEC MIX SCG is produced in Fine or Coarse mixtures and used to bond together adjacent masonry units, fill bond beams and occupy all areas around steel reinforcement in the cores of the masonry assemblage without mechanical consolidation or reconsolidation, while meeting ASTM C 476 and TMS 402/602 requirements for reinforced masonry construction.
SPEC MIX Self Consolidating Grout is available in 80 lb (36.2 kg) packages for easy hand loading or in 3,000 lb (1,360.7 kg) reusable bulk bags to be used with the various SPEC MIX silo systems.
GROUT PUMPS
EZG HP-20T4 Hog Pump
The triple use Hog Pump handles most types of construction material and is designed specifically for grout, mortar, and concrete. The front can be hitched onto a truck trailer to easily bring to job sites. The pump’s valve uses a reversible S-Tube which is safer and easier to use than traditional ball valve designs. The HP-20T4 is ideal for large pump jobs requiring grout, mortar or even pea stones.
- Pumps up to 20 yd3 per hour
- Only pumps up to 18 cubic yard per hour with 2” line
- Plus 1 control system with a DP250 digital display for diagnostic & monitoring
- 8 cu.ft. hopper capacity
- Handles up to ¾” aggregate
- Horizontal pumping distance 800 ft.; Vertical is 200 ft.
- Piston face PSI: 650
- 4″ bore
- 30″ stroke
- Powered by a 58 HP Kubota Diesel DOC Final Tier 4
EZG GH75 Grout Hog
After more than a decade of development and thousands of field tests, the Grout Hog® has been streamlined for convenience and efficiency. Each model includes a unique swiveling base that reduces the number of moves required by the forklift. These grout delivery systems can be operated via wireless remotes, allowing operators greater pour precision.
- Standard capacity ¾ yd3 (.57 m3)
- Material discharge rate of ¾ yd3 in 2½ minutes
- Remote control operation (forward/reverse of auger)
- 8′ (2.44 m) reinforced, collapsible dispensing hose (4″ diameter)
- A hydraulic flow rate of 10 gpm @ 2000 psi
- Handles up to ¾” (1.91 cm) aggregate
- Empty weight 985 lbs. (446.7 kg)
- Gross weight 3885 lbs. (1807.5 kg)
- Overall dimensions (L × W × H) 92″ × 41.5″ × 49″
EZG GPH75 Grout Power Hog
After more than a decade of development and thousands of field tests, the Grout Hog® has been streamlined for convenience and efficiency. Each model includes a unique swiveling base that reduces the number of moves required by the forklift. These grout delivery systems can be operated via wireless remotes, allowing operators greater pour precision.
- Standard capacity ¾ yd3 (.57 m3)
- Material discharge rate of ¾ yd3 in 2½ minutes
- Remote control operation (forward/reverse of auger)
- 8′ (2.44 m) reinforced, collapsible dispensing hose (4″ diameter)
Power Source
- Auxiliary hydraulic power – GH75
- 11.7 HP Honda Gas Engine – GPH75 (adds 450 lbs. of weight)
- Crane bail for higher reach and better access – GPHC75 (adds 2′ of height and 90 lbs. of weight)
- Wireless Remote
- A hydraulic flow rate of 10 gpm @ 2000 psi
- Handles up to ¾” (1.91 cm) aggregate
- Empty weight 985 lbs. (446.7 kg)
- Gross weight 3885 lbs. (1807.5 kg)
- Overall dimensions (L × W × H) 92″ × 41.5″ × 49″
EZG UGH75 Uphill Grout Hog
After more than a decade of development and thousands of field tests, the Grout Hog® has been streamlined for convenience and efficiency. Each model includes a unique swiveling base that reduces the number of moves required by the forklift. These grout delivery systems can be operated via wireless remotes, allowing operators greater pour precision.
- Standard capacity ¾ yd3 (.57 m3)
- Material discharge rate of ¾ yd3 in 2½ minutes
- Remote control operation (forward/reverse of auger)
- 8′ (2.44 m) reinforced, collapsible dispensing hose (4″ diameter)
- A hydraulic flow rate of 10 gpm @ 2000 psi
- Handles up to ½” (1.27 cm) aggregate
- Empty weight 1055 lbs. (478.5 kg)
- Gross weight 4055 lbs. (1839.3 kg)
- Overall dimensions (L × W × H) 100″ × 37″ × 50.5″
EZG UGPH75 Uphill Grout Power Hog
After more than a decade of development and thousands of field tests, the Grout Hog® has been streamlined for convenience and efficiency. Each model includes a unique swiveling base that reduces the number of moves required by the forklift. These grout delivery systems can be operated via wireless remotes, allowing operators greater pour precision.
- Standard capacity ¾ yd3 (.57 m3)
- Material discharge rate of ¾ yd3 in 2½ minutes
- Remote control operation (forward/reverse of auger)
- 8′ (2.44 m) reinforced, collapsible dispensing hose (4″ diameter)
- A hydraulic flow rate of 10 gpm @ 2000 psi
- Handles up to ½” (1.27 cm) aggregate
- Empty weight 1055 lbs. (478.5 kg)
- Gross weight 4055 lbs. (1839.3 kg)
- Overall dimensions (L × W × H) 100″ × 37″ × 50.5″
- Power Source
- Auxiliary hydraulic power – UGH75
- 11.7 HP Honda Gas Engine – UGHP75 (adds 420 lbs. of weight and 1′ of length & width)
- Crane bail for higher reach and better access – UGPHC75 (adds 90 lbs. of weight)
- – Wireless Remote
MultiQuip C30HD Concrete Pump
The C30HDGA grout & concrete pump offers uncompromising engine performance with excellent fuel efficiency in a quiet, smooth pumping package.
Pumps up to 25 cubic yards (19 cubic meters) per hour
Maximum aggregate size of 1/2-inch minus (12 mm)
45-hp (33.5 kW) fuel-injected Zenith gasoline engine ensures quiet, efficient performance
Standard 2-function 125-foot (37.5 meters) hardwired remote. Multi-function radio remote with full volume control (Optional).
Fully-enlclosed piston lubrication box and central lubrication grease station
Standard equipment includes a 3-inch (76 mm) x 90 degree pipe elbow, 3 x 2 x 28-inch reducer, and two 3-inch couplings (all raised ends)
Excellent choice for small-aggregate concrete pumping, masonry grout, shotcrete, pressure grouting, and more
MultiQuip LS300G Mortar Pump
Filling a niche that has been neglected, the Mayco LS300G Concrete Pump has the versatility to efficently place 2″ line mixes (3/8″ pea gravel, masonry grout, shotcrete), structural concrete containing up to 1.5″ aggregate, as well as everything in-between. Equipped with 6″ diameter concrete cylinders and utilizing a 24″ stroke ensures that the LS300G will smoothly pump even low slump concrete mix designs.
Joint Reinforcement
Hohmann & Barnard Joint Reinforcement
Hohmann & Barnard’s joint reinforcement products have long proven to be necessary for superior performance in masonry wall construction. Hohmann & Barnard’s Lox All® Truss-Mesh and Lox All® Ladder-Mesh are continuous lengths of joint reinforcement that are embedded into the horizontal mortar joints of masonry walls. Joint reinforcement has long proven to be necessary for superior performance of masonry wall construction, as it offers the following benefits:
- Reinforces a variety of masonry walls
- Greatly reduces cracking that can arise from thermal stresses
- Enhances resistance to water penetration, as cracks are controlled
- Increases lateral flexural strength
- Bonds exterior and interior masonry wythes together in composite walls
- Bonds masonry at intersecting walls and corners
- Increases elasticity
- Increases performance of masonry walls under various stresses
- Fabricated in conformance with ASCE/ACI 530 building code requirements for masonry structures, and ASTM A 951 (standard specification for masonry joint reinforcement)
GAUGES:
- Reinforcing can be STANDARD WEIGHT (9 ga x 9 ga), EXTRA HEAVY (3/16″ Side Rods x 9 ga Cross Rods) or SUPER HEAVY DUTY (all 3/16″)
AVAILABLE FINISHES:
- Mill Galvanized
- Hot Dip Galvanized
- Stainless Steel
DIMENSIONS:
- Packed 500’ per bundle (50 pcs. – 10′ long)
- Tri-Mesh, Twin-Mesh and Box-Mesh packed 250’ per bundle (25 pcs. – 10’ long)
- Corners and Tees packed 25 pcs per bundle
Wire Bond Ladder Wire
Wire-Bond Ladder Series design is a prefabricated reinforcement for embedment in the horizontal mortar joints of masonry. It is manufactured in 10′ 8″ lengths from wire conforming to ASTM A1064/A1064M, ASTM A82/ A82M
It consists of two or more parallel and deformed longitudinal wires welded to a perpendicular cross wire spaced 16″ O.C. Out-to-out spacing is approximately two inches less than the nominal thickness of the wall. Options include fixed and adjustable tabs, hook and eye configurations, adjustable loop tie and more.
- 16″ O.C. ladder design positions cross rods on web of block to allow core clearance.
- Simplifies rebar installation; centering utilizes strength of grout.
- Allows unrestricted flow of grout or loose fill insulation into CMU cells.
- Minimizes re-setting of joint reinforcement around rebar.
- Improves resistance to shrinkage cracking.
- Provides stronger bond with cross rods in web of block.
- Less time devoted to rebar installation, grout pouring.
- Meets ASCE/ACI 530 building code requirements for masonry structures and ASTM A 951 (standard specification for masonry joint reinforcing).
For More information, please visit: Wire-Bond Joint Reinforcement
Masonry Accessories
Hohmann & Barnard Rubber Control Joint
RS Series is a Rubber Control Joint designed for masonry walls at control joints
Extruded rubber material
Rubber material conforms to ASTM D-2000 2AA-805 with a durometer hardness of 80 (+ or – 5) when tested in conformance with ASTM D 2240
Hohmann & Barnard PVC Control Joint
S Series – PVC Control Joint, is a complete line of polyvinyl chloride control joints suitable for various wall conditions.
The PVC material conforms to ASTM D 2287 (Type PVC 654-4) with a durometer hardness of 85 (+ or – 5) when tested in conformance with ASTM D 2240
Hohmann & Barnard Concealed Lintel System
Architects can feel free to incorporate this classic look into prestigious edifices such as Houses of Worship, Libraries, Universities, or wherever the design calls for a statement of timeless and imposing beauty. Virtually any design incorporating flat or arched brickwork can be brought to fruition in conjunction with H&B’s job-specific concealed lintel systems.
Hohmann & Barnard Masonry Anchors
Hohmann & Barnard offers a full line of Masonry Anchors and ties for all your brick, block and stone needs. Builder’s Equipment and Supply carries seismic and non-seismic anchors, thermal anchors, as well as adjustable anchors. For more information about available options, please see Hohmann & Barnard Anchors & Ties.
Hohmann & Barnard Epoxy Anchors
Hohmann & Barnard’s new line of chemical anchoring and repair systems is designed to deliver outstanding performance in a wide range of circumstances, from basic chemical anchoring to meeting extreme load-bearing, seismic, and fire-resistant requirements with 100% pure epoxy products.
For More information, please visit: Hohmann & Barnard Epoxy Anchors
Wire-Bond PVC Control Joint
PVC Control Joint is designed for use in solid or cavity masonry wall construction at pilasters, columns, intersections or other joints. In long walls, control joints at 30-foot intervals are recommended to provide resilient resistance to cracking under stress of expansion and contraction. Extruded from a specially formulated PVC compound with 80 durometer hardness conforming to ASTM D 2240.
Wire-Bond Rubber Control Joint
Rubber control joints allow for expansion and contraction of masonry walls while reducing the possibility of air and water penetration. Designed for masonry walls at control joint.
Wire-Bond Expansion Joint
#3300 Expansion Joint is a Closed Cell Neoprene Sponge that can placed horizontally beneath relieving angle, or in the vertical expansion joint to act as a control joint.
Wire-Bond Control Joint Anchor
The #1700 Control Joint Anchor is designed for transferring loads across control joints while handling compression loads and controlling lateral movement.
MASONRY TUBS
HTS10 Steel Hog Trough
Our Steel Hog Troughs® are preferred for their mobility, durability and reliability.
The HTS10 Hog Trough comes standard with steel legs and forklift pocket access on all four sides.
- 10 cu.ft. capacity
- 10-gauge steel
- 165 lbs.
- Forklift access on every side
- Fits on Hog Cart® (sold separately)
HTS10W Steel Hog Trough with Wheels
Our HTS10W model provides greater mobility with two rigid and two swivel heavy duty casters.
- 10 cu.ft. capacity
- 10-gauge steel
- 185 lbs.
HT10 Heavy Duty Hog Trough
Our heavy duty steel hog troughs are available with legs or casters.
- 10 cu.ft. capacity
- 3/16 gauge steel
- 255 lbs.
- Built in 1″ channels allow for crane operation
HT10W Heavy Duty Hog Trough with Wheels
Our heavy duty steel hog troughs are available with legs or casters.
- 10 cu.ft. capacity
- 3/16 gauge steel
- 330 lbs.
- Built in 1″ channels allow for crane operation
HTP10 Poly Hog Trough
The Poly Hog Trough® is made of extremely hard, nonstick polyethylene. They are highly resistant to damage typical of heavy construction sites. The polyethylene functions in all temperatures and will not crack in cold weather.
- Empty weight 70 lbs. (31.80 kg)
- Capacity 10 cu.ft. (.28 m3)
- Overall dimensions (L × W × H) 57″ × 28″ × 24″
HTP10W Poly Hog Trough with Wheels
The Poly Hog Trough® is made of extremely hard, nonstick polyethylene. They are highly resistant to damage typical of heavy construction sites. The polyethylene functions in all temperatures and will not crack in cold weather.
- Empty weight 82 lbs. (37.19 kg)
- Capacity 10 cu.ft. (.28 m3)
- Overall dimensions (L × W × H) 57″ × 28″ × 24″
HTP10C Poly Hog Trough with Casters
The Poly Hog Trough® is made of extremely hard, nonstick polyethylene. They are highly resistant to damage typical of heavy construction sites. The polyethylene functions in all temperatures and will not crack in cold weather.
- Empty weight 130 lbs. (59 kg)
- Capacity 10 cu.ft. (.28 m3)
- Overall dimensions (L × W × H) 57″ × 28″ × 24″
MultiQuip Mud Tub
The Multiquip MUD TUB is the easy choice for supplying mortar to professional masons. It is engineered for durability & easy cleanup with two available models to meet your job requirements.
Metal Lath
CEMCO Expanded Metal Lath
CEMCO’s Diamond Metal Lath is a versatile base for cement plaster walls. It’s carefully formed diamond keys allow for proper embedment and keying of the scratch coat on all types of walls. Can be used with hand and machine applied plaster. This lath is available with or without Grade D asphalt paper backing. All CEMCO expanded metal lath is produced fromstandard G60 hot-dipped galvanized steel. G90 is available upon special request.
CEMCO Flat Rib Metal Lath
CEMCO’s CEMMESH Flat-Rib with K-Paper is a more rigid lath with 1/8” longitudinal ribs spaced at 3” on-center that provide for wider spacing between wooden or metal supports. Small openings provide for great keying of plaster.
CEMCO Hi-Rib Metal Lath
CEMCO’s 3/8” Hi-Rib Lath is the most rigid of all metal laths. With full 3/8” ribs running longitudinally, and a 1/8” rib between them, Hi-Rib lath is able to span up to 24” on center. This lath can be used in both vertical and horizontal applications. Please consult CEMCO’s Technical Services for specifics.
CEMCO Foundation Sill Screed
CEMCO’s #7 FHA Foundation Sill Screed is manufactured to provide both a ground for plaster finishes, and weep holes to allow for moisture to drain properly from the exterior plaster system. #7 Sill Screed is available in two grounds, 7/8″ and 1-3/8″, for exterior plaster systems.
CEMCO Casing Bead
A 26 gauge galvanized casing bead with various grounds used in conjunction with expanded polystyrene (EPS) foam insulation board. Provides a workable screed around doors and windows. Also available with holes so as to perform like a weep-screed.
CEMCO CEMCORNER
CEMCO’s CEMCORNER is used as an exterior corner reinforcement that has a nailing strip along both sides for faster installation and straighter corners. CEMCORNER was designed so that it is easier for Portland cement plaster to flow into the nose of the CEMCORNER. CEMCORNER is available in standard straight, straight arch, bullnose, bullnose arch, and a special bullnose-shortflange to accommodate almost every conceivable corner application.
CEMCO Corner Expansion Joint
CEMCO Double J Control Joint
CEMCO’s Double “J” (XJ-15) Control joint relieves stresses and strains in large plaster walls and ceilings. This product has expanded flanges for proper keying and easy application. Its unique design permits the plaster to key underneath the rolled edges for added adhesion while the walls expand and contract under typical conditions. The pull tape on the joint itself permits a clean finish when removed after the finish coat. CEMCO’s Double “J” Control Joint is manufactured from 26 ga. , G60 hot-dipped galvanized steel by Niles and distributed by CEMCO. G90 is also available upon special request.
CEMCO Soffit Drip Edge
The #12 Soffit Drip Edge is manufactured for soffit and recessed-window-head applications. The 45-degree slope allows water to weep out of the assembly. The drip edge provides a place for water to drip from, instead of traveling back along the soffit. Part of CEMCO’s Water Management Products for stucco, the accessory is fabricated from minimum 0.018-inch thick hot-dipped galvanized steel complying with ASTM A653, having a minimum G-90 coating complying with ASTM A925. Contact Don Pilz at dpilz@cemcosteel.com for any questions regarding this system.
CEMCO Solid Leg Control Joint
The #15 SOLID LEG Control Joint is manufactured for horizontal application on exterior plaster walls. The .30” gap in the V groove is designed to allow movement due to horizontal expansion and contraction of plastered walls. The 5½” x ¾” horizontal control joint has a 3” long upper solid flange that allows for water to weep out of the stucco cavity and a 1.5” long lower expanded metal flange that allows proper keying of plaster. The Control Joint is fabricated from minimum 0.018-inch thick hot-dipped galvanized steel complying with ASTM A653 having a minimum G90 coating complying with ASTM A924.
CEMCO M-Slide Expansion Joint
The M-SLIDE EXPANSION JOINT is manufactured for application where movement is anticipated. The self-aligning two-piece design allows for 1-inch vertical movement while maintaining a watertight assembly for plaster walls. M-Slide Expansion Joint is part of CEMCO’s Water Management line of stucco accessories fabricated from minimum 0.018-inch hot-dipped galvanized steel complying with ASTM A653 having a minimum G-90 coating complying with ASTM A 925.
CEMCO Dimpled Sefl-Furred Metal Lath
CEMCO’s Self Furred Diamond Metal Lath “Dimpled” is manufactured with a ¼” dimples in the lath. The dimples provide the necessary ¼” furring off the sheathing’s surface to allow for proper embedment and keying of the scratch coat on all types of walls. This lath is available with or without Grade D asphalt paper backing. All CEMCO expanded metal lath is produced from standard G60 hot-dipped galvanized steel. G90 is available upon special request.
CEMCO Metal Lath Products
CEMCO’s Metal Lath products include Expanded, Self-Furred, Paper-Backed, Cem-Mesh, Flat-Ribbed, and Hi-Ribbed produced from hot-dipped galvanized steel. Our full line of lath and plaster accessories includes Expansion and Control joint products by Niles, along with a multitude of screeds, weeps, corners, and architectural profiles. All CEMCO lath and plaster products meet or exceed industry standards and are certified code compliant via the ICC ES ESR#1623:
- Expanded Metal Lath
CEMCO’s versatile metal lath is ideal as a plaster base and reinforcement for all types of construction in walls, ceilings, and fireproofing of steel beams and columns.
Easy to cut and form to ornamental plaster work. Provides ample keying for scratch coat and is commonly used for plaster machine application. The expanded metal lath is available in 1.75, 2.5, and 3.4 pounds per square yard. All three of these are available in either flat, self-furred (dimpled of grooved), or in combination with paper-backing with D, Double-D, or K paper.
CEMCO Expanded Lath
- Flat Rib Lath
A more rigid lath that the diamond mesh, CEMCO’s Flat Rib lath with its 1/8” longitudinal ribs at 3” on center, provide for greater stiffness allowing wider spacing between wooden or metal supports.
Small openings provide for easy keying of plaster. CEMCO’s flat rib lath is also available in paper-backed in either K (Kraft) paper, commonly known as Cem-Mesh K, or with D or double D paper. As with all of CEMCO’s metal lath products, these too, are manufactured from high quality mill certified prime steel galvanized by the hot-dipped process to meet or exceed Federal Spec. No. QQL-101C, and ASTM A653 Grade 33 G-40 coating.
CEMCO Flat Rib Lath
- Hi Rib
The most rigid of CEMCO’s lath product line, the riblath has full 3/8” ribs running longitudinally through the lath 4” on center. Between each 3/8” rib is a 1/8” rib which provides for extra stiffness. The rigidity of this lath allows a span up to 24” on center for supporting members. CEMCO’s 3/8” rib is widely used for 1” solid partitions, ceilings, and walls and as reinforcements for concrete floor and roof slab.
Also available in this configuration is CEMCO’s 3/8” Hi Riblath Paper Backed with K (Kraft) paper in 3.4 pounds per square yard. Each sheet is backed with 3” strips of K paper between the ribs to prevent blow-through of spray applied plaster. All Cem-Lath and Cem-Rib products meet FederalSpecification QQ-L-101-C, UBC Chapter 25, and Federal Specification QQS-775-D.
CEMCO Hi Rib Lath
- Expansion Joint
As the premier provider of metal lath products to the construction industry, CEMCO offers expansion joints and expanded corner beads manufactured by Niles Building Products, Inc. These expanded metal trims and expansion joints are produced from hot-dipped galvanized steel that comply with ASTM C1063 and C841. Some products are also available in pure zinc on a special order basis. Corner trims are available in 1-A or 2-A Reinforced configurations in 8’, 9’, 10’, and 12’ lengths carefully packaged in heavy-duty cardboard boxes for easy shipment and storage.
Expansion joints are also made from high quality hot-dipped galvanized steel, and are available in double J, double V, #30 inside corner, and #40 adjustable configurations. Each of these products is manufactured to strict depth or ground dimensions to ensure the best finish possible in exterior plaster finishes. Available grounds include ¼”, 3/8”, ½”, ¾”, and 7/8”.
Also available from the CEMCO plaster accessories group is .093 pure-zinc control joint manufactured by Niles Building Products. Used specifically for interior applications, this gypsum board control joint is easily installed with staples, and a removable plastic strip for a clean, crisp joint line.
CEMCO Expansion Joints
- Corner Accessories
CEMCO provides along with its extensive metal lath and accessory product line, corner accessories for every application used by today’s contractors. CEMCOCORNER, a welded wire product is available in standard lengths to accommodate just about every situation seen in the field. CEMCO also provides expanded corners for exterior plaster systems in both 1A and reinforced 2A configurations, also available in various lengths.
CEMCO Corner Joints
- Screeds, Casings, Weeps
CEMCO manufactures several types of weeps, screeds, and casing beads for the exterior plaster industry. All are manufactured to tight tolerances using hot dipped galvanized steel that meets ASTM, Federal Specification, and FHA specifications.
Casing beads, sometimes referred to as stop beads, are available in either an expanded or solid flange, and with or without holes for weeping. The most common of these casing beads is the #66, which is available in grounds ranging from ¼” all the way up to 1 ¼”. All casing beads are delivered in cartons to protect the product until installation.
Weeps screeds do exactly what they are designed to do: weep water away from the structure through a series of holes. CEMCO’s No. 7 foundation screed is available in FHA (26 ga.) thickness steel, and in three depths: 4”, 5”, and the most common, 5 ½”. J-metal weeps channels are available in 26 gauge thick, in either a 1 ¾” flange, or 3 ½” flange, depending upon the application. The J-metal comes in grounds from 3/8” all the way to 1 3/8”, and with or without holes.
CEMCO Screeds, Casings, Weeps
- Patches
Patches are a recent development by CEMCO based on a timeless use of 2.5 diamond lath, but manufactured in strips or ‘patches’ to be used over door and window corners to greatly reduce cracking, by reinforcing stress areas. Patches can also be used as grout stop in masonry applications.
CEMCO Patches
- Water Management Products
The need for water management in stucco assemblies has become a major concern among contractors and architects. CEMCO has taken an active role in assisting the construction industry by introducing water management stucco accessories. All of the products in CEMCO’s new line of accessories will have dual functions. First, they will serve as stucco grounds to maintain the proper thickness. Second, they will be flashings to divert water away from the water-resistant barrier, a feat CEMCO achieved by extending the width of the attachment leg and removing the perforated nailing holes. CEMCO will also address the issue of stucco-accessory corrosion resistance by manufacturing the water management accessories in 25-gauge materials with a G-90 zinc coating.
CEMCO Water Management Products
MIXERS
EZG7 Manual Mixer
The EZG Mixers homogeneously combine heavy aggregates on the job site giving you as much time as you need—for any project—before the precast hardens. The manual dump mixers are triple use for grout, mortar, and concrete. They feature our #80 chain-driven system and are designed with bearings spaced from the seals to improve bearing durability.
- 1.5 to 2 bag capacity or 7 cu.ft. (.2 m3)
- 7.9 HP Honda Gas Engine (Standard)
- Mixes grout, mortar, and concrete
- Will mix up to 3/4″ (1.9 cm) aggregate
- Overall dimensions (L × W × H) 73″ (107″ with tongue) × 47″ × 58″ (67″ with dump handle)
- Discharges up to 21″ high
- 48″ load height
- Manual recoil start
- 3/16″ drum thickness
- Empty weight
- 850 lbs. (386 kg)
- 4″ × 6″ rectangular structural tubing
- 1 ¼” solid steel shaft
- 2″ ball hitch
- Overall dimensions (L × W × H) 73″ (107″ with tongue) × 47″ × 58″ (67″ with dump handle)
EZG9 Manual Mixer
The EZG Mixers homogeneously combine heavy aggregates on the job site giving you as much time as you need—for any project—before the precast hardens. The manual dump mixers are triple use for grout, mortar, and concrete. They feature our #80 chain-driven system and are designed with bearings spaced from the seals to improve bearing durability.
- 2 to 3 bag capacity or 9 cu.ft. (.25 m3)
- 7.9 HP Honda Gas Engine (Standard)
- Mixes grout, mortar, and concrete
- Will mix up to 3/4″ (1.9 cm) aggregate
- Discharges up to 20″ high
- 56″ load height
- Manual recoil start
- 3/16″ drum thickness
- Empty weight 970 lbs. (440 kg)
- 4″ × 6″ rectangular structural tubing
- 1 1/4″ solid steel shaft
- 2″ ball hitch
- Overall dimensions (L × W × H) 76″ (110″ with tongue) × 47″ × 67″ (77″ with dump handle)
EZG12 Manual Mixer
The EZG Mixers homogeneously combine heavy aggregates on the job site giving you as much time as you need—for any project—before the precast hardens. The manual dump mixers are triple use for grout, mortar, and concrete. They feature our #80 chain-driven system and are designed with bearings spaced from the seals to improve bearing durability.
- 3 to 4 bag capacity or 12 cu.ft. (.34 m3)
- 11.7 HP Honda Gas Engine (Standard)
- Mixes grout, mortar, and concrete
- Will mix up to 3/4″ (1.9 cm) aggregate
- Discharges up to 20″ high
- 56″ load height
- Manual recoil start
- ¼” drum thickness
- Empty weight 1231 lbs. (550 kg)
- 4″ × 7″ rectangular structural tubing
- 1 ¾” solid steel shaft
- 2″ ball hitch
- Overall dimensions (L × W × H) 76″ (110″ with tongue) × 47″ x 67″ (77″ with dump handle)
Mud Hog MH9 Hydrolic Mixer
Specially designed to handle even the toughest jobs, EZG’s Mud Hogs are engineered for job site durability and easy operation. Mixers are triple use and intended for low loading and high dumping to further reduce labor fatigue. Our innovative, patented system design uses rubber blades on vertical paddles to allow reversibility, prevent splashing and reduce clogging issues typical of other mixers on the market.
- 2 to 3 bag capacity or 9 cu.ft. (.25 m3)
- 8.5 HP Honda Gas Engine (Standard)
- Will mix up to 3/4″ (1.9 cm) aggregate
- Discharges up to 26″ high
- Empty weight 1325 lbs. (601.1 kg)
- Gross weight 2675 lbs. (1213.4 kg)
- Hydraulic dump system
- Hydraulic drive system
- Manual recoil start
- ¼” drum thickness
- Overall dimensions (L × W × H) 94″ × 35″ × 54″
Mud Hog MH12 Hydrolic Mixer
Specially designed to handle even the toughest jobs, EZG’s Mud Hogs are engineered for job site durability and easy operation. Mixers are triple use and intended for low loading and high dumping to further reduce labor fatigue. Our innovative, patented system design uses rubber blades on vertical paddles to allow reversibility, prevent splashing and reduce clogging issues typical of other mixers on the market.
- 3 to 4 bag capacity or 12 cu.ft. (.34 m3)
- 11.7 HP Honda Gas Engine (Standard)
- Will mix up to 3/4″ (1.9 cm) aggregate
- Discharges up to 49″ high
- Empty weight 1695 lbs. (768.8 kg)
- Gross weight 3495 lbs. (1588 kg)
- Hydraulic dump system
- Hydraulic drive system
- Manual recoil and electric start
- 3/8″ drum end and ¼” drum wrap thickness
- Overall dimensions (L × W × H) 82″ x 42″ x 49.5″
Mud Hog MH20 Hydrolic Mixer
Specially designed to handle even the toughest jobs, EZG’s Mud Hogs are engineered for job site durability and easy operation. Mixers are triple use and intended for low loading and high dumping to further reduce labor fatigue. Our innovative, patented system design uses rubber blades on vertical paddles to allow reversibility, prevent splashing and reduce clogging issues typical of other mixers on the market.
- 6 to 7 bag capacity or 20 cu.ft. (.57 m3) – ¾ cubic yard
- 11.7 HP Honda Gas Engine (Standard)
- Will mix up to 3/4″ (1.9 cm) aggregate
- Discharges up to 51″ high
- Empty weight 2295 lbs. (1041 kg)
- Gross weight 5295 lbs. (2406 kg)
- Hydraulic dump system
- Hydraulic drive system
- Manual recoil and electric start
- 3/8″ drum end and 5/16″ drum wrap thickness
- Overall dimensions (L × W × H) 96″ x 44″ x 53″
Mobile Mud Hog MMH4
The Mobile Mud Hog® was built to allow easy pours in difficult terrain. Four different mobile models are available, ranging from our compact 4 cu.ft. unit to our largest 20 cu.ft. unit. With a range of capacities and options to choose from, you can easily find a model that meets your needs.
- 4 cu.ft. (.11 m3) mixing capacity
- 4 – 80 lb. bags of pre-blended mix (add water only)
- Will mix up to ¾” (1.91 cm) aggregate
- Hydraulic drive system
- Manual gate dump
- 3/16′ drum thickness
- Minimum hydraulic flow rate – 4 gpm @ 2000 psi
- Maximum hydraulic flow rate – 16 gpm @ 3000 psi
- Empty weight 350 lbs. (159 kg)
- Gross weight 950 lbs. (431 kg)
- Overall dimensions (L × W × H) 29″ ×44″ ×29″
Mobile Mud Hog MMH9
The Mobile Mud Hog® was built to allow easy pours in difficult terrain. Four different mobile models are available, ranging from our compact 4 cu.ft. unit to our largest 20 cu.ft. unit. With a range of capacities and options to choose from, you can easily find a model that meets your needs.
- 9 cu.ft. (.25 m3) mixing capacity
- 9 – 80 lb. bags of pre-blended mix (add water only)
- Will mix up to ¾” (1.91 cm) aggregate
- Hydraulic drive system
- Manual gate dump
- ¼” drum thickness
- Minimum hydraulic flow rate – 4 gpm @ 2000 psi
- Maximum hydraulic flow rate – 26 gpm @ 3000 psi
- Empty weight 600 lbs. (272 kg)
- Gross weight 1950 lbs. (885 kg)
- Overall dimensions (L × W × H) 55″ × 33″ × 42″
Mobile Mud Hog MMH12
The Mobile Mud Hog® was built to allow easy pours in difficult terrain. Four different mobile models are available, ranging from our compact 4 cu.ft. unit to our largest 20 cu.ft. unit. With a range of capacities and options to choose from, you can easily find a model that meets your needs.
- 12 cu.ft. (.34 m3) mixing capacity
- 12 – 80 lb. bags of pre-blended mix (add water only)
- Will mix up to 1″ (2.54 cm) aggregate
- Hydraulic drive system
- Hydraulic gate dump
- ½ cubic yard per minute discharge rate
- Minimum hydraulic flow rate – 10 gpm @ 2000 psi
- Maximum hydraulic flow rate – 40 gpm @ 3000 psi
- 3/8″ drum end and ¼” drum wrap thickness
- Empty weight 1000 lbs. (454 kg)
- Gross weight 2880 lbs. (1306 kg)
- Skid mount and forklift pockets
- Overall dimensions (L × W × H) 66″ × 40″ × 44.5″
Mobile Mud Hog MMH20
The Mobile Mud Hog® was built to allow easy pours in difficult terrain. Four different mobile models are available, ranging from our compact 4 cu.ft. unit to our largest 20 cu.ft. unit. With a range of capacities and options to choose from, you can easily find a model that meets your needs.
- 20 cu.ft. (.57 m3) mixing capacity
- 20 – 80 lb. bags of pre-blended mix (add water only)
- Will mix up to 1″ (2.54 cm) aggregate
- Hydraulic drive system
- Hydraulic gate dump
- ½ cubic yard per minute discharge rate
- Minimum hydraulic flow rate – 10 gpm @ 2000 psi
- Maximum hydraulic flow rate – 40 gpm @ 3000 psi
- 3/8″ drum end and 5/16″ drum wrap thickness
- Empty weight 1400 lbs. (635 kg)
- Gross weight 4400 lbs. (1996 kg)
- Skid mount and forklift pockets
- Overall dimensions (L × W × H) 80″ × 50″ × 55″
MultiQuip 9Cf Mortar Mixer
Whiteman mixers have the features, quality and engineering excellence preferred by the contractor and the equipment rental industry.
- Super-strong tubular steel frame with forklift pocket
- Mixes 9-cubic feet (248 liters) of material
- Honda GX240 gasoline engine
- High tensile strength paddle arms
- Thick 14-gauge steel engine cover resists vibration
- Powder coat paint with a durable lasting finish
MultiQuip 12cf Mortar Mixer
No one manufacturer offers such an extensive variety of tried and tested plaster/mortar mixers designed to meet your needs.
- Powered by a reliable Honda GX390 gasoline engine
- Mixes up to 12 cubic feet (340 liters) of material
- Greatly reduced maintenance – no V-belts, pulleys, clutches or gears
- Hydraulic dump increases production reduces operator fatique
- Hydraulic drive mixes larger lower slump loads – ideal for high-production requirements
MultiQuip MC94SH8 9cf Mortar Mixer
This 9-cubic-foot (248 liters) is the ultimate in heavy-duty concrete mixers.
- Powered by reliable Honda GX240 engine
- Heavy-duty tubular steel frame with forklift pocket
- Capacity is 9 cubic feet (248 liters)
- Rugged 14 gauge steel engine cover resists vibration
- Spring suspension standard for less bounce, sway
- Powder coat paint with a durable long-lasting finish
Moisture Management
Hohmann & Barnard Drip Edges
Our Standard Drip Plate, furnished with a smooth, factory-formed hemmed edge for installation safety and uniform appearance.
Standard DP Drip Plates are compatible with all H&B flashing products.
Hohmann & Barnard X-Barrier Peel & Stick Barrier
X-Barrier™ is a sheet applied self-adhesive, membrane to provide an air and water barrier when applied to above grade wall assemblies. X-Barrier is a self-adhered membrane that resists air leakage and water penetration and acts as a vapor barrier.
Hohmann & Barnard Liquid Flash
Liquid-Flash is formulated using a high performance silyl-terminated polyether polymer technology (STPE). It is a single component, moisture cure elastomeric waterproofing membrane that is applied and tooled to create a long-term moisture proof barrier. Liquid-Flash shows excellent resistance to UV degradation and extreme environmental conditions. Can be applied to damp or wet substrates without outgassing or “bubbling”. Safe to apply in wet conditions when rain is eminent as it will not wash off like other sealants. Because Liquid-Flash is 100% solids it will not shrink or crack. It is compatible with most common building materials, including concrete, plywood, concrete masonry, brick, gypsum sheathing, wood and cement based sheathings.
Hohmann & Barnard Envior-Barrier
ENVIRO-BARRIER™ is a single component, fluid applied, elastomeric membrane to provide an air, water and vapor barrier when applied to above grade wall assemblies. It cures to form a resilient, monolithic, fully adhered elastomeric membrane which resists air leakage and water penetration plus acts as a vapor barrier.
Hohmann & Barnard Envioro-barrier VP
ENVIRO-BARRIER™ VP is a single component, fluid applied, elastomeric membrane to provide a vapor permeable air and water barrier when applied to above grade wall assemblies. It cures to form a resilient, monolithic, fully adhered elastomeric membrane which resists air leakage and water penetration but allows vapor diffusion.
Hohmann & Barnard EB Spray Tape
Hohmann & Barnard ENVIRO-BARRIER™ Spray-Tape is a spray or brush applied detail flashing for Hohmann & Barnard Air Barriers. It is designed to seal door/window openings, terminations, edges of patches, and overlaps in detail areas.
MORTARS
Spec Mix PLS Mortar
SPEC MIX® Portland Lime & Sand mortar is a dry preblended mortar mix containing Portland cement, hydrated lime and dried masonry sand formulated for superior bond, water retention and board life. Available in Types M, S and N, each meets ASTM C 270 and ASTM C 1714 requirements. SPEC MIX Portland Lime & Sand is available in standard or custom colors. In addition, custom mix designs are available for specific applications or properties, the standard Portland Lime & Sand mortar is designed to be compatible with the characteristics of the specified masonry unit. It is acceptable for all types of masonry construction with submittals available upon request. It may be used above or below grade when manufactured to the appropriate specification. SPEC MIX® Portland Cement, Lime & Sand Mortar is available in 80 lb. (36.3 kg.) packages for easy hand loading or in 3,000 lb. (1360.8 kg.) reusable bulk bags to be used with the various SPEC MIX® silo systems.
SPEC MIX® Portland Cement, Lime & Sand Mortar is available in 80 lb. (36.3 kg.) packages for easy hand loading or in 3,000 lb. (1360.8 kg.) reusable bulk bags to be used with the various SPEC MIX® silo systems
Spec Mix Masonry Cement and Sand
SPEC MIX® Masonry Cement & Sand mortar is a dry preblended mortar mix containing masonry cement and dried masonry sand formulated for superior bond, water retention and board life. SPEC MIX Masonry Cement & Sand mortar is available in color and is engineered for the installation of CMU, brick, and stone unit applications where high mortar workability and board life is required for good bond. It comes in Types M, S and N, and each designation meets ASTM C 270, ASTM C 1714, and CSA A179 requirements.
SPEC MIX® Masonry Cement & Sand Mortar is available in 80 lb. (36.3 kg.) packages for easy hand loading or in 3,000 lb. (1,360.8 kg.) reusable bulk bags to be used with the various SPEC MIX silo systems.
Spec Mix Masonry Cement and Sand
SPEC MIX® Mortar Cement & Sand mortar is a dry preblended mortar mix containing mortar cement and dried masonry sand formulated for superior bond, water retention and board life. Available in Types M, S, and N, each meets ASTM C 270, ASTM C 1714 and CSA A179 requirements. SPEC MIX Mortar Cement & Sand is available in color and is formulated for the installation of CMU, brick, and stone applications where high mortar workability and board life is required for good bond.
SPEC MIX® Mortar Cement & Sand is available in 80 lb. (36.3 kg.) packages for easy hand loading or in 3,000 lb. (1,360.8 kg.) reusable bulk bags to be used with the various SPEC MIX® silo systems.
Spec Mix IWR Mortar
SPEC MIX® Integral Water Repellent (IWR) Mortar is specially formulated to reduce water penetration and efflorescence of masonry mortar joints. By incorporating a proprietary, dry polymeric integral water repellent admixture during the SPEC MIX manufacturing process, the designer, specifier, owner and contractor are assured the mortar on their project will repel moisture, while maintaining optimal workability and flexural bond strength.
SPEC MIX® Mortar Cement & Sand is available in 80 lb. (36.3 kg.) packages for easy hand loading or in 3,000 lb. (1,360.8 kg.) reusable bulk bags to be used with the various SPEC MIX® silo systems.
Spec Mix Adhered Veneer Mortar
SPEC MIX® Adhered Veneer Mortar (AVM) is a specially formulated mortar for use in the installation of thin veneer masonry units. It contains an optimal blend of dry cementitious materials, masonry sand, and performance enhancing admixtures specifically designed for use as a scratch coat, bond coat and joint grout for thin veneer masonry units. It is formulated as a cohesive material with consistent workability, high water retention and excellent bond strength. The final wall system will produce a non-load bearing, aesthetically pleasing exterior veneer or interior finish on concrete or masonry walls, stud walls or metal buildings.
SPEC MIX® Adhered Veneer Mortar is available in 80 lb. (36.3 kg.) packages for easy hand loading or in 3,000 lb. (1,360.8 kg.) reusable bulk bags to be used with the various SPEC MIX® silo systems.
Spec Mix Polymer Modified Adhered Veneer Masonry Mortar
SPEC MIX® Polymer Modified Adhered Veneer Mortar (PMAVM) is a technologically advanced adhered veneer mortar for use in bonding adhered manufactured stone veneer, natural thin cut stone and thin brick to a cementitious substrate. PMAVM is designed to provide excellent workability, cohesion, high bond strength, sag resistance, water resistance, efflorescence minimization, and durability. SPEC MIX PMAVM is the ideal solution for architects and contractors with projects where an immediate and ongoing need for mortar delivering high bond strength and sag resistance during installation is required. In applications where mortar joints are not utilized, such as dry stack applications, SPEC MIX PMAVM should be used to gain additional bond strength and “pop-off” protection. Installing natural thin cut stone veneer is aided by the unique anti-sag and high bond properties of SPEC MIX PMAVM.
SPEC MIX® Polymer Modified Adhered Veneer Mortar is available in 80 lb. (36.3 kg.) packages for easy hand loading or in 3,000 lb. (1,360.8 kg.) reusable bulk bags to be used with the various SPEC MIX® silo systems.
Spec Mix XP 500 Thin Veneer Adhesion Mortar
SPEC MIX® Thin Veneer Adhesion Mortar XP500 is a premium preblended polymer modified thin set mortar specifically designed to bond masonry thin veneer units including manufactured and gauged or ungauged natural thin stone and thin brick to substrates for interior and exterior installations. Its innovative, anti-sag formulation and optimized sand gradation provide superior workability, adhesion and durability crucial to the application.
SPEC MIX Thin Veneer Adhesion Mortar XP500 is available in 50 lb (22.6 kg) packages for easy hand loading. Also available in 3,000 lb (1,360.7 kg) reusable bulk bags to be used with the various SPEC MIX silo delivery systems.
Parex USA Masonry Veneer EPS Basecoat and Adhesive
EPS Basecoat & Adhesive is the first premium grade basecoat used to adhere and coat EPS continuous insulation sheeting as part of the Parex USA MVS – CI System. This specialized EPS Basecoat creates an energy efficient wall substrate suitable for the application of manufactured masonry veneers or in conjunction with other Parex USA finishes.
55 lb. (25 kg) net weight in plastic pails.
Parex USA Masonry Veneer Adhesive
Parex USA Masonry Veneer Adhesive is a polymer modified Portland cement setting adhesive for installing ceramic tile, stone and thin brick over Ci, stucco, cement board and CMU. It is used for exterior applications. It bonds to most surfaces and is freeze thaw stable.
50 lbs. (22.7 kg) net weight in multi-wall bags.
Laticrete MVIS Premuim Pointing Mortar
MVIS Premium Pointing Mortar is a premium factory prepared high performance, fast setting masonry pointing mortar that provides a masonry pointing mortar joint that is dense and hard. Featuring a consistent color, anti-microbial additive that is idea for interior and external florrs and walls. Available in 50 lb Bags
Laticrete MVIS Pointing Mortar
MVIS Pointing Mortar is for adhered stone, thin brick and manufactured masonry veneers. Factory prepared and designed to be mixed with water. Available in 50 lb Bags
Laticrete MVIS Epoxy Pointing Mortar
MVIS™ Epoxy Pointing Mortar is a high performance epoxy pointing mortar that offers excellent color uniformity, durability, stain resistance and sanitary full joints in an easy-to-use, non-sag formula.
Epoxy Pointing Mortar Data Sheet | Epoxy Pointing Mortar Marketing Brochure | Epoxy Pointing Mortar Installation Guide | Epoxy Pointing Mortar SDS | Epoxy Pointing Mortar Part B SDS | Epoxy Pointing Mortar Part C SDS | Epoxy Pointing Mortar Health Product Declaration | Epoxy Pointing Mortar Warranty
Laticrete MVIS Lightweight Mortar
MVIS Lightweight Mortar is a lightweight, high performance multi-use, polymer fortified adhesive mortar. Incredible non-sag performance, including large and/or heavy thin brick, stone, masonry veneer, or tile
- Exceeds ANSI A118.4, 118.11 & 118.15 Requirements
- Lightweight formula. A 30 lb (13.6 kg) bag provides the same coverage as a 50 lb (22.7 kg) bag of traditional mortar.
- Bonds to many suitable substrates
- Unique color options are now available in all LATICRETE® grout colors when mixed with PERMACOLOR® Select Color Kits*
Lightweight Mortar Data Sheet | Lightweight Mortar SDS | Lightweight Mortar SDS North America I | Lightweight Mortar SDS North America II | Lightweight Mortar SDS North America III | Lightweight Mortar SDS North America IV | Lightweight Mortar Health Product Declaration | Lightweight Mortar 10 Year Warranty | Lightweight Mortar 15 Year System Warranty | Lightweight Mortar 25 Year System Warranty
Laticrete MVIS Hi-Bond Veneer Mortar Rapid
The ultimate, rapid setting polymer fortified, thin-set mortar for interior and exterior installation of masonry veneer, quarry tile, pavers and brick. Ultimate adhesion for masonry veneer
- Rapid Set Mortar; can be grouted/pointed in 2–4 hours
- Incredible bond to exterior glue plywood* and concrete
- Excellent shear bond strength
- High performing smooth creamy formula
- Contains antimicrobial protection to inhibit the growth of stain-causing mold and mildew in the substrate
- Exceeds ANSI A118.4 & ANSI A118.11 Shear Bond Strength Requirements
- Exceeds ASTM C270 compressive strength requirements for masonry veneer Installations.
- LATICRETE® 25 Year System Warranty (United States and Canada) for masonry veneer installations over concrete and masonry substrates**
* Interior use only.
** When used as a component of the LATICRETE® 25 Year System Warranty (United States and Canada)(DS-025.0)
Available in 25 lb bag.
Hi-Bond Rapid Veneer Mortar Data Sheet | Hi-Bond Rapid Veneer Mortar Marketing Brochure | Hi-Bond Rapid Veneer Mortar SDS | Hi-Bond Rapid Veneer Mortar Environmental Product Declaration | Hi-Bond Rapid Veneer Mortar Health Product Declaration | Hi-Bond Rapid Veneer Mortar Product Warranty | Hi-Bond Rapid Veneer Mortar 15 Year System Warranty
Laticrete MVIS Hi-Bond Veneer Mortar
The ultimate, polymer fortified, thin-set mortar for interior and exterior installation of masonry veneer, stone, ceramic tile, quarry tile, pavers and thin brick. Ultimate adhesion for masonry veneer
- Incredible bond to exterior glue plywood* and concrete
- Excellent shear bond strength
- High performing
- smooth and creamy formula
- Contains Microban® antimicrobial protection to inhibit the growth of stain causing mold and mildew in the substrate
- Exceeds ANSI A118.4
- ANSI A118.11 and ANSI A118.15
- Exceeds ASTM C270 compressive strength requirements for masonry veneer installations
- Passes IBC and IRC shear bond strength code requirements for adhered masonry veneer when tested in accordance with ASTM C482
- Conforms to ISO 13007-1 with a classification of C2TES1P1
- LATICRETE® 25 Year System Warranty (United States and Canada) for masonry veneer installations over concrete and masonry substrates**
* Interior Only.
** When used as a component of the LATICRETE® 25 Year System Warranty (United States and Canada) (DS 025.0)
Available in 50 lb Bag
Laticrete MVIS Thin Brick Mortar
MVIS Thin Brick Mortar is a multi-use, polymer fortified adhesive mortar.
- Incredible non-sag performance, including large and/or heavy thin brick, stone, masonry veneer or tile
- Exceeds ANSI A118.4, 118.11 & 118.15 Requirements
- Smooth and creamy consistency
- “Extra Heavy” rating per ASTM C627 (TCNA)
- Bonds to many suitable substrates
- Available in 50 lb bag
Laticrete MVIS Veneer Mortar
MVIS Veneer Mortar is a patented, versatile polymer fortified mortar designed specifically for the installation of adhered masonry veneer, natural manufactured stone and thin brick.
- Incredible non-sag performance – faster, easier installations
- Revolutionary patented formula provides maximum bond strength to veneers and substrate
- Exceeds ASTM C270 compressive strength requirements for masonry veneer installations
- Passes IBC and IRC shear bond strength code requirements for adhered masonry veneer when tested in accordance with ASTM C482
- Mixes only with water – no admix needed
- Fiber-reinforced
- Available in 40 lb Bag
Laticrete MVIS Premium Mortar Bed
MVIS Premium Mortar Bed is a polymer fortified blend of carefully selected polymers, portland cement and graded aggregates.
- For use as a scratch or finish coat in place of Type S or Type N mortar
- Polymer fortified – no need for latex additives
- Premixed – no job site blending of powders required
- Economical – saves time and money
- High strength formula
- Pumpable for large scale veneer projects
- Exceeds ASTM C270 compressive strength requirements for masonry veneer installations.
- Available in 60 lb Bag
LaFarge Holcim Portland Cement
Portland Cement is a basic building material, which is used in a wide variety of commercial and architectural concrete construction applications. Concrete made with Portland Cement using the proper mix design can be resistant to the attack of harsh environmental influences, such as frost and de-icing chemicals.
- Type I: General Use
- Type II: Moderate Sulfate Resistance
- Type III: High Early Strength
- Type V: High Sulfate Resistance
- I White: for unique architectural designs
- Portland Cement is supplied in bulk quantities (tons) or 42 kilograms (92 pound) bags for Type I, Type I/II, Type IA, Type II (MH) and Type V or 21 kilograms (46 pound) bags for Type I and Type
LaFarge Holcim Mortar Cement
Mortar Cement is a formulated cementitious material manufactured to be used in producing masonry mortars for use in brick, block and stone masonry units. Mortar Cement mortars are recommended for above- and below-grade load bearing walls where higher bond strengths are needed. Mortar Cement can also be used to produce stucco, a versatile facing material that can be applied to wall or ceiling surfaces to achieve special architectural finishes.
Mortar Cement is available in the following packaging size (bag) Type M 36.3 kilogram (80 pound) Type S 34 kilogram (75 pound) Type N 31.8 kilogram (70 pound)
Cimsa Supre White White Portland Cement
With the superior strength characteristics it has, it provides far more strength beyond grey cements and it is primarily preferred by especially precast producers. It is preferred in the building chemicals sector for both its superior adhesive strength and also high level of whiteness.
Lehigh White Masonry Cement
Masonry cement consists of portland or blended cement, plasticizers, and an air entraining agent. Air-entraining agents protect mortar from freeze-thaw damage and provide additional workability. The specific components of masonry cement may vary depending on the manufacturer and local construction practices. ASTM C91 defines masonry cement by physical requirements and performance properties rather than ingredients.
Type N: For normal masonry construction.
Type S: For masonry structures that require higher strength than Type N.
Lehigh White Portland Cement
Cement types are defined by a variety of standards and specifications. Portland cements conform to the American Society for Testing and Materials (ASTM) C150 Standard Specification for Portland Cement and Canadian Standards Association (CSA) A3001. Some cements may meet multiple types. All Lehigh Cement products are manufactured to comply with applicable CSA, ASTM, AASHTO or API Standards.
Alamo Masonry Cement
Mortar cement is specially formulated and manufactured to produce masonry mortar for use in brick, block, and stone masonry construction. Mortar cement mortars have similar attributes to masonry cement mortars, but they have lower air contents than masonry cements, and the mortar cement specification includes a minimum bond strength requirement. Mortar cement mortars are appropriate for use in structural applications that require masonry with high flexural bond strength.
Alamo Portland Cement
Cement types are defined by a variety of standards and specifications. Portland cements conform to the American Society for Testing and Materials (ASTM) C150 Standard Specification for Portland Cement and Canadian Standards Association (CSA) A3001. Some cements may meet multiple types. All Lehigh Cement products are manufactured to comply with applicable CSA, ASTM, AASHTO or API Standards.
SAWS
Arbortech AllSaw
Engineered to significantly improve safety and efficiency when cutting brick walls, mortar and more. The ALLSAW Masonry Restoration Kit is ideal for Masonry Professionals. There are a number of specialized blade options designed to tackle even the hardest of applications from single brick to caulking removal.
Bosch 7-1/4″ Circular Saw
Featuring a powerful 15 Amp, high output motor, Bosch’s CS10 7-1/4 In. circular saw offers fast, smooth cutting at a variety of different angles. A durable magnesium footplate means increased stability and precision accuracy. Weighing in at just 10.3 Lbs., the Bosch CS10 is easy to handle and comfortable to use. An unobstructed view of the cut line means better visibility for more exact cuts. With a soft grip handle for added comfort, and a blower for better dust control, this is one user-friendly tool. The CS10 also features a 56-degree bevel capacity, along with positive detents at 22.5 degrees and 45 degrees for working on a wide variety of projects.
Bosch 18V Jig Saw
The Bosch JSH180 Lithium-ion 18V jig saw is compact and lightweight. Its T-shank blade change system allows the user to insert the blade just without the need for any tools, and when it’s time for a blade change, a turn of knob ejects the blade, so there is no need to touch a hot blade. This jig saw also features an always-on blower and integrated LED light for enhanced visibility in the cutting area. The sophisticated electronics package includes Electronic Motor Protection (EMP), which protects the motor against overload and ensures a long lifetime and the Electronic Cell Protection (ECP) protects the battery (sold separately) against overload, overheating and deep discharge. Bosch 18V Lithium-ion batteries feature the CoolPack design with a special heat-conductive housing and ribbing that cools them by drawing out heat out, providing battery life of up to 100% over Lithium-ion batteries without the CoolPack design.
Dewalt 60V Max Brushless 7-1/4″ Circular Saw
Our most powerful tools just got better with the FLEXVOLT 60V MAX* 7-1/4 in. Cordless Circular Saw with Electric Brake. It has up to 47% more power than the DCS575 60V MAX* Circular Saw** with 2456 unit watts out. It combines the power of a corded circular saw with the portability and convenience of cordless thanks to revolutionary DEWALT FLEXVOLT technology that offers a no-load speed of 5800 RPM.
Husqqarna MS 360 Masonry Saw
The Husqvarna MS 360 3 HP Masonry Saw is equipped with a patented water management system that minimizes water use by a unique distribution which keeps the workpiece dry and the workplace clean. Cuts a full 5in. deep with included Vari-Cut Turbo masonry blade. Head rotates to 22.5° and 45° angles to get the right cutting angle. Easily moved by two people with built-in telescoping handles. Gain productivity, time and effort with the MS 360 3 HP masonry saw. Ideal for use on pavers, bricks, stone, and concrete block.
Husqqarna K970 14″ Cut-Off Saw
Sturdy, reliable, light and powerful – the K 970 power cutter is ready to perform when you are. The ultimate choice when you need an all-round cutter performing in the toughest conditions, withstanding climate and fuel variations. Suitable for road works when used with the corresponding KV 970 trolley. The trolley also means you can fully concentrate on the cutting job.
Husqvarna K4000 Electric Saw
This electric all-round cutter minimises the amount of water and slurry. Unlike other electric cutters, the blade rotates forward, cutting into the material efficiently with minimum effort on the operator. K 4000 is easily adaptable for dry cutting with the Vac attachment accessory for minimal dust generation.
Husqvarna MS 610 Masonry Saw
Husqvarna MS 610 5 HP, 230 V, 20″ 1-ph 60 Hz Masonry Saw
STIHL Cutquick Cut-Off Saw
The 14” STIHL TS 700 cut-off machine is the powerhouse of the STIHL line. Designed for superior handling during the toughest jobs, this machine features a powerful, high-speed engine, large fuel capacity, five-point dual element vibration control system built right into the handle, and a semi-automatic belt tensioner with an innovative ribbed belt. Its X2 filtration system is low maintenance and cleans airflow with nearly 100 percent efficiency, reducing downtime for filter maintenance. Each component on this machine was meticulously engineered with demanding professionals in mind.
STIHL Rock Boss Concrete Cutter
When you need to cut deep into concrete, reach for the Boss – the STIHL GS 461 ROCK BOSS®. This revolutionary concrete cutter changes the game with enhanced performance that cuts up to 15.7” deep into concrete, reinforced concrete (with rebar up to ½ inch), cinder blocks, masonry bricks, asphalt and soft stone. And it does all of this in a compact, lightweight package that is easy to maneuver and transport.
STUCCOS
Spec Mix Fiber Base Coat
SPEC MIX® Fiber Base Coat (FBC) is a dry, preblended cement based stucco engineered with proprietary admixtures and fibers that are computer batched for consistency and performance unmatched by traditional field mixed stucco. SPEC MIX FBC has a custom blended sand gradation that increases the wall flexural strength while reducing cracking and crazing. The custom sand gradation also provides excellent workability and finishing properties for the applicator over a traditional field-mixed source.
SPEC MIX® Fiber Base Coat is available in 80 lb. (36.2 kg.) packages for easy hand loading or in 3,000 lb. (1,360.7 kg.) reusable bulk bags to be used with the various SPEC MIX® silo systems.
Spec Mix Scratch and Brown Coat
SPEC MIX® Scratch and Brown Preblended Stucco is a dry, preblended cement based stucco basecoat to be used as the scratch and/or brown coat in a three-coat stucco application. SPEC MIX Scratch and Brown has a custom blended sand gradation that increases the walls flexural strength while reducing cracking and crazing. SPEC MIX Scratch & Brown is computer batched for consistency and performance that is unmatched by traditional field mixed stucco. The custom sand gradation also provides excellent workability and finishing properties for the applicator over a traditional field-mixed source.
SPEC MIX Scratch & Brown Preblended Stucco is available in 80 lb (36.2 kg) packages for easy hand loading or in 3,000 lb (1,360.7 kg) reusable bulk bags to be used with the various SPEC MIX silo systems.
Spec Mix Scratch and Brown Fiber Reinforced Stucco
SPEC MIX® Scratch & Brown Fiber Reinforced Stucco is engineered and preblended to provide superior consistency and durability when used as the scratch and/or brown coat in three-coat wall systems. SPEC MIX Scratch & Brown Fiber Reinforced Stucco is a custom blend of cementitious materials, additives, aggregates and alkali resistant fibers meeting ASTM C 926 requirements. The special sand gradation used provides excellent workability and finishing properties for the applicator as well as increases the flexural strength of the wall while reducing cracking and crazing common with traditional field-mixed stucco. To ensure uniformity and quality, each ingredient of the finished product is individually weighed before all the raw materials are thoroughly blended, bagged and delivered.
SPEC MIX Scratch & Brown Fiber Reinforced Stucco is available in 80 lb (36.2 kg) packages for easy hand loading or in 3,000 lb (1,360.7 kg) reusable bulk bags to be used with the various SPEC MIX silo systems.
LaHabra Perma-Prime
An acrylic-based primer that reduces the chance of efflorescence which may result from the cement content of various bases. Enhances the appearance and uniformity of the finish. Water-vapor permeable. Does not create a vapor retarder. Improves finish coverage.
60 lb (27.2 kg) net weight in plastic pails.
LaHabra Perma-Flex Stucco Grade Acrylic Finish
A 100% acrylic-based textured finish for stucco only. Made with Dirt Pick-Up Resistance (DPR) meaning the surface of the finish hardens and does not soften again under heat. The non-tacky surface provides high resistance to accumulation of dirt, mold, and pollutants. The finish is integrally colored with high quality pigments.
LaHabra Perma-Flex Stucco Grade Acrylic Finish is available in four textures: Fine, Swirl, Smooth, and Coarse
65 lbs. (29.5 kg) net weight in plastic pails
LaHabra Perma-Finish EIFS & Stucco Acrylic Finish
A 100% acrylic-based textured finish. Made with Dirt Pick-Up Resistance (DPR) meaning the surface of the finish hardens and does not soften again under heat. The non-tacky surface provides high resistance to accumulation of dirt, mold, and pollutants. The finish is integrally colored with high quality pigments.
LaHabra Perma-Flex Stucco Grade Acrylic Finish is available in four textures: Fine, Swirl, Smooth, and Coarse
65 lbs. (29.5 kg) net weight in plastic pails
LaHabra Perma-Elastic Elastomeric Finish
A 100% acrylic-based elastomeric textured finish. Made with DPR (Dirt Pick-up Resistance) chemistry. Is highly flexible: can bridge pre-existing or existing hairline cracks. Integrally colored with high quality pigments.
LaHabra Perma-Elastic Elastomeric Finish is available in three textures: Fine, Coarse, and Swirl.
65 lbs. (29.5 kg) net weight in plastic pails.
LaHabra Exterior Stucco Color Coat
LaHabra Exterior Stucco Color Coat provides a lasting, durable color finish over LaHabra Fiber-47 Fastwall Scratch & Brown, LaHabra Fastwall Stucco Base, Portland cement plaster “brown coat” and Parex USA Stucco Level Coat. It is integrally colored with fade-resistant pigments, and is economical with low maintenance. Product is available in premix or tint Base.
LaHabra Exterior Stucco Color Coat is available in the following bases/aggregate size for use with LaHabra Color Packs: Base 11 16/20, Base 100 20/30, Base 200 16/20, Base 200 20/30
90 lb. (40.8 kg) net weight in a multi-wall bag.
LaHabra Santa Barbara Mission Finish
LaHabra Santa Barbara Mission Finish provides a lasting, durable smooth stucco finish over LaHabra Fiber-47 Fastwall Scratch & Brown, LaHabra Fastwall Stucco Base, exterior plaster “brown coat” and Parex USA Stucco Level Coat. It is integrally colored with fade-resistant pigments, and is economical with low maintenance. Product is available in premix or tint Base.
LaHabra Santa Barbara Mission Finish is available in 2 bases for use with LaHabra Color Packs: Base 100 and Base 200
90 lb (40.8 kg) net weight in a multi-wall bag.
LaHabra FastWall Stucco Base Concentrate
A factory controlled high-quality blend of Portland cement, lime, fibers and proprietary additives that conforms to ASTM C926. ASTM C897 or ASTM C144 sand is added at the job site. Can be installed up to 1/2 in. (12.7mm) in one application.
80 lb (36 kg) net weight in a moisture resistant bag.
LaHabra FastWall Stucco Base Sanded
A factory controlled high-quality blend of Portland cement, lime, fibers, proprietary additives and ASTM C144 sand that conforms to ASTM C926. Factory-blended mix that requires only the addition of water. Can be installed up to 1/2 in. (12.7mm) in one application.
80 lb (36 kg) net weight in a moisture resistant bag.
LaHabra FastWall Accel-Cure
Excellent as a base for smooth finishes. No moist curing required. High PSI. High tensile strength. Under normal conditions, ready to accept finish after 24 hours. Fastwall Accel-Cure is a factory controlled high-quality blend of Portland cement, lime, fibers and proprietary additives that conforms to ASTM C926. ASTM C897 or ASTM C144 sand is added at the job site. Can be installed up to 1/2 in. (12.7mm) in one application.
80 lb (36.3 kg) net weight in moisture resistant bag.
LaHabra Fiber 47 Scratch and Brown Concentrate
A factory controlled high-quality blend of Portland cement, lime, fibers and proprietary additives that conforms to ASTM C926 is designed as a replacement to job-site mixed scratch and brown base coats. ASTM C897 or ASTM C144 sand is added at job site.
80 lbs. (36 kg) net weight in a multi-wall moisture resistant bag.
LaHabra Insul-Bond Dry Base Coat & Adhesive
A base coat for LaHabra EIFS. Adhesive to laminate EPS to listed substrates. Used in a 50% acrylic paste to 50% Portland cement by weight ratio. Requires the addition of Portland cement.
55 lb (25 kg) net weight in plastic pails.
LaHabra Insul-Bond Wet Base Coat & Adhesive
A base coat for LaHabra EIFS. Adhesive to laminate EPS to listed substrates. Used in a 50% acrylic paste to 50% Portland cement by weight ratio. Requires the addition of Portland cement.
55 lb (25 kg) net weight in plastic pails.
Parex USA Variance Specialty Finishes
From old world venetian plasters and textured Tuscan stucco to natural stone looks, Variance Specialty Finishes provide the best in design and quality in high-end decorative surface finishes.
Endless color and texture possibilities are made available for the interior and exterior of new or existing structures.
For more information, please visit: Variance Specialty Finishes
Parex USA 355 Standard Mesh
4.5 oz fiberglass 38 in. (96.5 cm) wide mesh. Is highly flexible for full walls or details. Is alkali-resistant. Standard reinforcement of Parex USA EIFS walls for impact resistance and details. Required in combination with 358.14 High Impact Mesh or 358.20 Ultra High Impact Mesh. May be used in Parex USA Krak-Shield
Parex USA 356 Short Detail Mesh
4.5 oz fiberglass 9.5 in. (24 cm) wide mesh. Is highly flexible for use on details. is alkali-resistant. Ideal for use in back wrapping, corners, reveals and trim. May be used in combination with 355, 358.6 & 358.10 meshes in Parex USA Krak-Shield assemblies.
WALL BRACING
Hog Leg Wall Bracing System
Safely securing new masonry projects, especially high walls, is tantamount to safe and solid construction. Hog Legs® wall braces are lightweight, adjustable poles which easily anchor into your footings and helps keep setting block in place.Each wall brace fastens through the head joints, which means no block cutting or anchor bolts are required. The standard kit covers jobs up to 400 linear feet.The Hog Legs are effective with any type of masonry block. Every brace system comes with a lockable, 8′ storage rack that makes your Hog Legs brace system easy to store.
Hog Leg Extension Kit
Safely securing new masonry projects, especially high walls, is tantamount to safe and solid construction. Hog Legs® wall braces are lightweight, adjustable poles which easily anchor into your footings and helps keep setting block in place.Each wall brace fastens through the head joints, which means no block cutting or anchor bolts are required. The standard kit covers jobs up to 400 linear feet.The Hog Legs are effective with any type of masonry block. Every brace system comes with a lockable, 8′ storage rack that makes your Hog Legs brace system easy to store.
WEATHER BARRIERS
Parex USA WeatherSeal Spray & Roll-On
A 100% acrylic elastomeric waterproof membrane and air barrier which can be either rolled, brushed, or spray applied. Extremely flexible: can bridge cracks and accommodate small movements up to 1/32 in. (.8mm). Designed for use as water-resistive barrier behind LaHabra EIFS or stucco. Bridges 1/4 in. (6mm) gaps at sheathing board joints with 396 Sheathing Tape embedded.
55 lb (25.0 kg) net weight in plastic pails
Parex USA WeatherTech WeatherSeal SB
A single component cement base waterproofing coating for CMU and concrete. It is a multipurpose polymer modified waterproofing product: Air Barrier, Water Resistive Barrier, and Scratch Coat that can be used above grade and below grade for planters or concrete foundations.
Parex USA WeatherSeal SB is can be used to fill joints in CMU and to level rough concrete or CMU walls.
50 lbs. bag (22.68 kg)
Prosoco R-Guard Cat 5
Cat 5 is a single-component, silyl-terminated polymer (STP) that is roller-applied to produce a highly durable, seamless, elastomeric weatherproofing membrane on exterior sheathing, CMU back-up walls, and pre-cast concrete. Cat 5 is proven to prevent water and air penetration of the building envelope in conditions ranging from everyday weather to the drenching rains and 155-mph winds of a Category 5 hurricane.
Use Cat 5 as the primary air barrier over above-grade structural surfaces prepared with Joint & Seam Filler and FastFlash. Solvent-free. Isocyanate-free. Phthalate-free. Complies with all VOC regulations.
Available in 5-gal
Prosoco R-Guard Cat 5 Rain Screen
R-Guard Cat 5 Rain Screen is a fluid-applied, waterproofing, and air and water barrier membrane that combines the best of silicone and polyurethane properties. This single-component, silyl-terminated polymer (STP) is specially formulated to meet the unique requirements of pressure-equalized rain screen construction. The roller-applied air and waterproof barrier produces a highly durable, seamless, elastomeric weatherproof membrane on exterior sheathing behind open-jointed or vented rain screen cladding. Cat 5 Rain Screen is proven to prevent water and air penetration of the building envelope in conditions ranging from everyday weather to the drenching rains and 155-mph winds of a Category 5 hurricane. Cat 5 Rain Screen can be applied in unfavorable weather conditions to dry or damp substrates. This feature eliminates many weather-related construction delays and accelerates the “drying in” of new buildings. The durable, elastomeric membrane adheres to most surfaces, is immediately waterproof and is compatible with most sealants and waterproofing or air barrier components.
Available in 5-gal
Prosoco R-Guard Spray Wrap MVP
PROSOCO R-Guard® Spray Wrap MVP is a fluid-applied air and water-resistive barrier that stops air and water leakage in cavity wall, masonry veneer construction, as well as in stucco, EIFS and most other building wall assemblies. Once on the substrate, the easily applied liquid quickly dries into a rubberized, highly durable, water-resistant, vapor-permeable membrane.
Spray Wrap MVP provides superior protection against water intrusion while minimizing potential for condensation within walls. The durable membrane conforms and adheres to most common building surfaces and is compatible with most paints, sealants, and self-adhered waterproofing or air barrier components.
Utilize Spray Wrap MVP as the primary air barrier over above grade wall assemblies prepared with R-Guard Joint & Seam Filler and/or R-Guard FastFlash.
Available in 5-gal & 55-gal
Laticrete MVIS Air & Water Barrier
MVIS Air & Water Barrier is single component, load bearing, fluid applied, waterproofing, crack isolation, air barrier membrane.
- Meets ASTM E2357 Air Leakage of Building Assemblies.
- Adhered Exterior veneers may be installed to membrane using Polymer Fortified Veneer Mortars over concrete, brick, cement plaster and cement backer board.
- Excellent bond strength.
- Contribute to overall building energy efficiency.
- Equipped with anti-microbial technology.
- Works together with MVIS Transition Tape and MVIS Flexible Sealing Tape to help provide complete protection of the building envelope.
- Meets ASTM D 1970 Nail Sealability requirements.
- Lighter color for ease of inspection.
- Safe—no solvents and non-flammable.
- MVIS Air & Water Barrier is an Air Barrier Association of America (ABAA) Evaluated Material and is part of an ABAA Evaluated Assembly.
- Exceeds ANSI A118.10 and A118.12
- Available in 5 gal Pail
Air & Water Barrier Data Sheet | Air & Water Barrier Marketing Brochure | Air & Water Barrier SDS | Air & Water Barrier HPD | Air & Water Barrier ICC ES AC212 | Air & Water Barrier GREENGUARD Certificate | Air & Water Barrier ASTM E2357-11 | Air & Water Barrier ABAA Certificate | Air & Water Barrier Product Warranty | Air & Water Barrier 15 Year System Warranty
Laticrete MVIS Flexible Sealing Tape
MVIS Flexible Sealing Tape is a flexible, stretchable, and tear resistant flashing detail tape that allows for easy installation in awkward configurations such as arched window or door openings, I-beams, and other wall penetrations. MVIS Flexible Sealing Tape is a self-adhering air, vapor and weather barrier that protects structures from air, vapor, wind, and rain. MVIS Flexible Sealing Tape is a stretchable flashing tape made from an elastic non-woven polyolefin factory laminated to a proprietary adhesive. It can be used as a transition material with MVIS Air & Water Barrier where different substrates meet to provide continuity.
Hohmann & Barnard Envior-Barrier
ENVIRO-BARRIER™ is a single component, fluid applied, elastomeric membrane to provide an air, water and vapor barrier when applied to above grade wall assemblies. It cures to form a resilient, monolithic, fully adhered elastomeric membrane which resists air leakage and water penetration plus acts as a vapor barrier.
Hohmann & Barnard Envioro-barrier VP
ENVIRO-BARRIER™ VP is a single component, fluid applied, elastomeric membrane to provide a vapor permeable air and water barrier when applied to above grade wall assemblies. It cures to form a resilient, monolithic, fully adhered elastomeric membrane which resists air leakage and water penetration but allows vapor diffusion.
GCP Dry-Block Mortar Admixture
As an integral admixture, DRY-BLOCK® Mortar Admixture provides bond enhancement and water penetration resistance throughout the depth of the mortar joint. DRY-BLOCK® Mortar Admixture’s water-repellent properties will prevent the moisture from wicking through the mortar joint into the building’s interior. Likewise, it will not be wicked back to the exterior carrying soluble salts that can cause efflorescence at the joints on the wall exterior.
GCP Perm-A-Barrier
The PERM-A-BARRIER® portfolio provides watertight, airtight air barrier systems and full field technical support for flexibility and high-performance compatibility with a project’s building envelope design. Broad product range for any wall design or design requirement. Our air barrier membranes and accessories are designed to work together and are rigorously tested to meet building code requirements. The end result is a truly optimized wall design that’s sustainable over time.
For More information, please visit: GCP Perm-A-Barrier
Tnemec Pirme-A-Pell 200
Prime-A-Pell 200 is a clear, filmless, penetrating water repellent for virtually all above-grade, vertical concrete, stucco, block and brick masonry. Concrete, stone and masonry treated with Prime-A-Pell 200 resist water intrusion, stain damage, freeze/thaw spalling, efflorescence and rust damage. The treatment does not alter the color or texture of the surface, nor significantly affect the vapor transmission qualities of the substrate. The solution penetrates the substrate and chemically reacts to create a powerful barrier against water penetration. This barrier is resistant to ultraviolet and weather deterioration.
WALL SCRUBBER
EXZG HW3000 Hog Waller Masonry Wall Scrubber
The Hog Waller Masonry Wall Scrubber is an excellent heavy duty masonry wall cleaning tool, loosening excess mortar with a 7″ abrasive disk and removing it from the wall through a built in vacuum system.
- Machine weight 12 lb. (5 kg)
- Extends from 51” to 65”
- 10” guard with built in vacuum
- 7” abrasive disc
- Vacuum bag with 81” hose
- Comes with carrying case
- LED flashlight provided
- Quicker, easier wall clean-up
- Does the work of 4 to 5 men to save money and time
- Durable and easy to service
WATER REPELLENTS
Prosoco Sure Klean Blok-Guard & Graffiti Control
Blok-Guard & Graffiti Control is a water and graffiti repellent formulated to weatherproof custom masonry units, cast stone, architectural concrete block, precast concrete, wood and other porous masonry materials. It protects masonry surfaces from repeated graffiti attacks without altering the surface’s natural appearance. Treated surfaces resist penetration of most types of graffiti.
Available in 5-gal
Prosoco Sure Klean Blok-Guard & Graffiti Control II
Blok-Guard & Graffiti Control II is a clear-drying, water-based silicone emulsion for weatherproofing concrete block and other porous masonry materials. Blok-Guard & Graffiti Control II protects interior and exterior masonry surfaces from graffiti attacks without altering the natural appearance.
Blok-Guard & Graffiti Control II also protects exterior walls exposed to normal weathering. Graffiti removal from treated surfaces is fast and easy using Defacer Eraser® Graffiti Remover. Blok-Guard & Graffiti Control II is easy to apply with low-pressure spray. Controls rainwater penetration through exterior block walls and helps control efflorescence, mildew and other moisture-related stains. Treated surfaces exhibit excellent surface beading and do not trap moisture.
Available in 5-gal & 55-gal
Prosoco Weather Seal Natural Stone Treatment
Sure Klean® Weather Seal Natural Stone Treatment is a modified siloxane water repellent developed for limestone, marble and most other traditional masonry surfaces. Natural Stone Treatment penetrates deeply to provide long-lasting protection without altering the natural appearance of the substrate. Unlike conventional siloxane water repellents, Natural Stone Treatment is modified for effectiveness on most limestone, marble and other calcareous surfaces. This product provides water repellent protection superior to more common silane, siloxane, acrylic or metallic stearate water repellents. Natural Stone Treatment reduces the severity of biological staining common to regions with high relative humidity. Treated surfaces resist dark staining and degradation caused by fungal growth, mold and mildew.
Available in 1-gal, 5-gal, & 55-gal
Prosoco Weather Seal Natural Stone Treatment WB Plus
Sure Klean® Weather Seal Natural Stone Treatment WB Plus is a water-based water repellent for limestone, marble and travertine that delivers the same performance as solvent-based products, without the drawbacks of traditional water-based treatments. VOC-compliant, ready-to-use, and low-odor, this modified siloxane water repellent was developed to provide long-lasting penetrating protection. Compared to conventional water-based water repellents for limestone, marble and travertine, Weather Seal Natural Stone Treatment WB Plus has greater water repellency, longer service-life and is less likely to stain. Use of this product will not alter the substrate’s natural texture but may cause some darkening. Always test to ensure desired results before overall application.
Available in 1-gal, 5-gal, & 55-gal
Prosoco Weather Seal Siloxane PD
Sure Klean® Weather Seal Siloxane PD (predilute) is a ready-to- use, water-based silane/siloxane water repellent for concrete and most masonry and stucco surfaces. Siloxane PD will not impair the natural breathing characteristics of treated surfaces. It helps masonry resist cracking, spalling, staining and other damage related to water intrusion. Low odor and alkaline stable, Siloxane PD is ideal for field and in-plant application.
Available in 1-gal, 5-gal, & 55-gal
Prosoco Weather Seal Gloss ‘N Guard WB
Sure Klean® Weather Seal Gloss ‘N Guard WB is a highly durable, water-based, acrylic protective coating for tile, pavers, terrazzo and other decorative paving, as well as burnished concrete block and architectural custom masonry. Gloss ‘N Guard WB dries to a satin-gloss finish which enhances the natural beauty of treated surfaces. It guards against water penetration and makes mortar smears and other construction soiling easier to remove. When applied in-plant to burnished concrete block or architectural custom masonry, Gloss ‘N Guard WB protects against the scrapes and scuffs of transport. Following construction cleaning, the treatment deepens and enriches the color of burnished block and makes maintenance cleaning faster and easier, while helping protect against weathering.
Available in 1-gal & 5-gal
Prosoco Stand Off Limestone & Marble Protector
Stand Off Limestone & Marble Protector is a clear, penetrating water and oil repellent suitable for use on interior or exterior calcareous surfaces such as limestone, marble and travertine. It’s also suitable for many other types of masonry surfaces. Limestone & Marble Protector penetrates deeply to provide surface and subsurface protection without forming a glossy surface film. Treated surfaces retain their natural color, texture and appearance. Limestone & Marble Protector combines high quality siloxane resins with “oleophobic” resins to produce a penetrating water and oil repellent ideal for long-term protection against food, oil and waterborne staining. Unlike conventional penetrating oil repellent products, Limestone & Marble Protector has been modified to ensure effectiveness on limestone, marble and other calcareous or neutral-pH surfaces.
Available in 1-gal & 5-gal
Prosoco Weather Seal Color Enhancer WB
Sure Klean® Weather Seal Color Enhancer WB is a long-lasting, penetrating water repellent that deepens and enriches the natural color of porous, stone, concrete and tile, including most clay, concrete and porous natural stone paving. The water-based blend of siloxane resins is ideal for enhancing the color intensity of new surfaces and reviving faded, weathered colors to better than new – inside or out. Treated surfaces also repel water, and the dirt, salt and contaminants water carries. Easy-to-apply Color Enhancer WB helps surfaces look better, last longer and clean up more easily. It will not trap water vapor within the substrate, alter the natural texture of treated surfaces or fade or “yellow” from lengthy exposure to sunlight.
Available in 1-gal & 5-gal
Prosoco Paver Kare Paver Enhancer
Paver Kare Paver Enhancer is a solvent-based blend of high-quality siloxanes modified to provide excellent water repellency and color enhancement to interlocking concrete, fired clay, porous tile and many types of natural stone surfaces. Paver Enhancer penetrates and reacts with the surface to form a chemical bond, providing long-term durability, alkali resistance and superior breathability.
Available in 1-gal & 5-gal
